YONA FRIEDMAN La principal materialización de la teoría de la “arquitectura móvil” de Yona Friedman sería su concepto de “ciudad espacial” (ville spatiale 1959). Esto es, estructuras flotantes tridimensionales -en las que la disposición de sus elementos puede variar- que se incorporan al trazado urbano de ciudades, o también a zonas no urbanizables, como embalses, marismas o terrenos agrícolas, con problemas demográficos. Estas mallas modulares sobreelevadas ayudarían a paliar los endémicos problemas de habitabilidad y convivencia que sufren las grandes urbes contemporáneas, pues según Friedman, permitirían multiplicar la superficie habitable en ciudades y zonas metropolitanas colapsadas, creando varios niveles urbanos independientes entre sí, tanto desde un punto de vista estético como funcional, que quedarían conectados por una serie de grandes pilares en cuyo interior habría diversos mecanismos (ascensores, escaleras) que posibilitarían la circulación vertical. “Me interesan los elementos que se pueden cambiar libremente, asegura Yona Friedman, las ciudades en las que lo que hay arriba es independiente de lo que hay abajo (…) y en la que la vida urbana no esté necesariamente a ras del suelo” (entrevista realizada por el arquitecto holandés Winy Mass, julio de 2003, publicada en el libro KM3 Excursions on Capacities del estudio de arqui- tectura MVRDV). CIUDADES SUPERPUESTAS.pdf UTOPÍAS REALIZADAS.pdf UTOPÍAS REALIZABLES.pdf En sus “ciudades espaciales”, las construcciones tendrían que cumplir tres características fundamentales: tocar la mínima superficie de suelo posible; ser desmontables y desplazables; y ser modificables según los deseos de sus habitantes. En opinión de Friedman -que ha imaginado aplicaciones específicas de este concepto para urbes como Túnez, París, Venecia o Nueva York-, esa superposición de capas independientes pero permanentemente interconectadas propiciaría la coexistencia no conflictiva de espacios industriales, comerciales, administrativos, culturales y residenciales. Todo ello en una extensión de territorio abarcable, de modo que el crecimiento demográfico no obligaría a trasladar a amplios sectores de la población (normalmente, los más desfavorecidos) fuera del entramado urbano, enclaustrándolos en barrios periféricos con escasos equipamientos y muy mal comunicados con el resto de la ciudad. Partiendo de las ideas formuladas en su texto Propositions africaines (1958), Yona Friedman ha llevado a cabo varios proyectos en países en vías de desarrollo de Asia, África y América del Sur en los que ha apostado por la combinación de técnicas de cons- trucción autóctonas con métodos arquitectónicos contemporáneos. En este sentido, una de sus iniciativas más emblemáticas es el ya citado Museum of Simple Technology de Madras (India), construido a partir de materiales de la zona como el bambú y en el que puso en práctica una de las nociones que ha articulado todo su discurso teórico: la implicación activa en la concepción y planificación de un edificio de sus futuros usuarios. En esta línea también podemos destacar proyectos de la década de los setenta como la fábrica Dubonnet (Ivry, Francia) o el instituto Bergson (Angers, Francia). Texto extraído de la hoja de sala de la exposición Yona Friedman. Utopías realizables. Centro Andaluz de Arte Contemporáneo, 2006.
¿Aprende a diseñar espacios con luz del sol? La iluminación natural en arquitectura ¡al detalle! Mira efectos, tipos, características, herramientas, guías y más
屋外階段の描き方です。まずおおまかな形でとらえてから細部を描きます。手描きパースの描き方ブログ手描きパースのワザやコツをたくさん掲載しています。 ↓…
Con los libros pasa como con muchas otras cosas. La tecnología amenaza con desplazarlos por la proliferación de nuevas formas de leer.
TGIF! I got you some very cutesie, fun and tasty goodies from the web. Enjoy! Een mooie dag en een mooie editie van What I love friday. Ik heb hele mooie, creatieve dingen gevonden op het wereldwijde web. Kijk maar mee :) Polka dot inside-and-out birthday-cake by Handmade Charlotte. De ultieme confetti taart! Confetti's erin,…
Berlin-based Carmeq GmbH, part of the Volkswagen Group, hired Actincommon to give their office an update to allow the employees more flexibility with how and where they worked
Important information points and dimensions about the kitchen, living room, lighting, closet, laundry, drainage system, types of stairs, etc, by 07sketches.
using a traditional modular system and prefab structure, penda's 'a thousand yards' pavilion is set to occupy a 30,000 m2 site at beijing's 2019 horticultural expo.
Architectural model making guide from First In Architecture looks at tools, materials, styles and techniques to help you make your architectural model.
'Furniture is often more important in our lives than architecture,' says the celebrated Japanese architect, as he discusses his long-term collaboration..
Project Description | Project003 requires us to design a block which can present the void space and solid material with each other when they are aggregated together. Meanwhile, CNC router is the machine we need to use in this project. The material of the frameworks is foam with which we are going to cast 6 blocks. On the other hand, reusing the molds is an important issue for the project. After casting, those blocks are going to be aggregated together and the voids hence are completed, furthermore, the compositions have to present the relationship among the blocks. Erwin Hauer's works may be reference for us because strong relationship between void and solid is represented in his works. Void Block, T.C. Kurt Hong, Summer 2015 Design | I try to keep the same design element in this series of models. The wormhole-like form is the element I want to continue. In the first project, I tried to use fabric to create the void space, and this wormhole-like shape is generated at that time. During project 2, I kept the shape and turned it into solid, aggregated them and obtain a series of variation. Thus, this time I turned it back to void space again and used it to generate the space and connect all blocks with this void. Therefore, the design started from the continuous void space (an endless wormhole which connect two diagonal vertexes of a block), I cut the void space with the surfaces among 9 blocks and insert the each part back to each corner of a block. Continuous voids pace through blocks Re-arranging the void spaces While aggregating them together, the separated void spaces are connected together and hence complete the original void space. Further, although only shallow void spaces show up in the elevation of the composition, the diagonal perspective shows the penetration of the void space. Viewer can look though the all the blocks and the spaces blocked by the blocks thus connected. Rhino model of the Void Block Aggregation of blocks Error Propagation | The goal of this project is to deliver the digital model to physical world as possible as we can, hence, overcoming the errors which may occur in each phase. Although the errors in each step are slight, however, the propagation of the errors can cause a huge distortion in the final result. Also, the aggregation of the errors is a serious problem. Therefore, controlling the error or compensating the effects may be the most difficult part in this project. Diagram of Undercut The software for CNC router we used is MasterCam, which is a toolpath simulation software and and can generate the milling code for us. The setting of the router is complex and the drillbits have many limits. Milling process of CNC Router The components milled by CNC router Before milling the components, we have to check if there is any "undercut" in the file. Undercut is not allowed in CNC router because the router cannot mill the undercut part and will ignore it. And, the draft angle also has to be considered in advance, or the de-molding will be very difficult. Secondly, we must leave a thin skin among each component because it is not allowed to drill through the material. Hence, the thickness will be the first error which is inevitable and the thickness cause the mismatch while assembling. Furthermore, the density of the foam is an crucial issue while de-molding, however, the high density foam is too thick to fit into the machine. Thus, the robot arm became a foam cutter (thanks to Asa for his kindly help!) for us. Asa and his robot arm When milling was done, we made some de-molding tests to figure out how to take off the frameworks from plaster without damages. We are going to use the same molds to cast 4 to 6 models, hence the molds need to be protected well. We tried Murphy's oil, dish soap, rough surface, polished surface, tape and the wrap plastic. The conclusion is: wrap plastic. Wrapped component De-molding of the Void Block Although the wrap plastic can prevent the plaster from sticking on the foam, the plastic is hard to wrap on the component without wrinkles. Moreover, the texture of the foam and the router are both covered by the plastic. In some cases, the designer wants to keep the trace of the tools (router), however, this is a trade off. After all preparation works, the plaster still caused the largest error in the whole process, even though we cast so many models before. The curing time, mix proportion and the material of mold we use are all different from those before, so there were still many unexpected problems. Void Block, T.C. Kurt Hong, Summer 2015 4 Void Blocks, T.C. Kurt Hong, Summer 2015 6 Void Blocks, T.C. Kurt Hong, Summer 2015 Review | We talked about "unexpected" factors during review. Because the goal of this project is to deliver the digital form to real world as possible as you can. Thus, I feel that the material is only the media for representing the "ideal" model in digital world. However, the real model still has its magic because of the light, the shadow, the color and the tactility of plaster, and the traces left by plastic. All those real things can not be shown in Rhino. To connect the gap between digital and physical is the mission of digital technology group, but what we need to do is not only single directional but bi-directional. To deliver a digital form to real world completely is not the whole but a small part of digital technology, most part of digital technology is to deliver the real world to virtual environment.
Las casitas del árbol son generalmente espacios en los que los niños pueden relacionarse de manera lúdica con la naturaleza. Estos espacios han sido desde siempre uno de los lugares favoritos de los niños, quienes se divierten escalando, corriendo, entrando y saliendo entre las ramas de los árboles, desde donde pueden apreciar hermosos paisajes llenos de vegetación.
Imagen 7 de 35 de la galería de Ganador Archiprix Chile 2013: Paseo Gastronómico y Centro Cultural / Santiago Beckdorf. Croquis
Ce modèle de résidence d’artiste n’est rien de moins qu’artistique. Il est de forme cubique et se décline en trois configurations différentes. Ce qui distingue ce modèle des autres, c’est qu’il utilise le verre en tant que murs afin de montrer les poutres de la maison, révélant sa
17 Photographs That Display Perfect Symmetry
space filling patterns - thinking about A. F. Wells' idea for 'nodes and linkers'
Image 35 of 35 from gallery of [5x17]Daecheong-dong Small House / JMY architects. Model 2
Grafton architects y Shell Arquitectos han proyectado la nueva sede de la UTEC conciviéndola como un nuevo acantilado hecho de hormigón. El edificio ha sido seleccionado como finalista en los Mies Crown Hall Americas Prize 2014 / 2015, unos premios que reconocen las mejores obras construidas en América del Norte y del Sur.
Image 8 of 14 from gallery of "A Kit of Parts": Mobile Classrooms by Studio Jantzen. Courtesy of Studio Jantzen