The Shop Fox W1669 34" Benchtop Radial Drill Press boasts a 1/2 HP motor that smoothly powers the five spindle speeds ranging from 550 to 3000 RPM. The headstock can be tilted 45° left, 90° right, and slid forward or backward over the column allowing you full adjustability. To make sure that you get the best use of the 9-3/4" diameter table. The drill press features rack-and-pinion elevation controls-adjustable 9-1/2" vertically, 90° tilt (left and right) and is capable of 360° rotation around the column. The W1669 can easily drill holes through plastic, fiberglass, and composites, and has a maximum capacity to drill through a half inch of steel without bogging down. The JT33 keyed drill chuck is fitted to the JT-33 spindle taper and offers up to 3-1/4" of travel. The chuck accepts drill bits from 1/16" to 5/8". You can set the adjustable threaded depth stop for predetermined and repeatable drilling."}},"base-catalog-309625973":{"__typename":"BaseProduct Motor: 1/2 HP, 110-Volt Swing: 33-1/2 in. Drill chuck: 1/16 in., 5/8 in. Arbor: JT-33 Spindle travel: 3-1/4 in. Range of speeds: 550 RPM to 3470 RPM
Radial drill press
The Shop Fox W1668 13-1/4" Oscillating Drill Press was awarded Top Value by WOOD Magazine because of its versatility. The W1668 can be used for efficient contour sanding in addition to traditional drilling, saving you the cost of buying a separate sander. As one grizzly.com customer review mentions, "this Benchtop Oscillating Drill Press is a good compromise for a small shop without room for two separate devices." The W1668 is fitted with a 1 to 16mm JT33 keyed drill chuck, offers up to 3-1/8" of travel, and a drilling capacity of 5/8" through mild steel. With the oscillating feature, the oscillating stroke length is 3/4". The 12-3/8" diameter, round table allows for drilling and surface sanding at different angles as it tilts 90° in both directions. The table has a clearance hole for use while sanding. This clever design incorporates a 2" dust collection port so that sanding is less messy."}},"base-catalog-309625973":{"__typename":"BaseProduct Motor: 1/2 HP, 110-Volt Swing: 34 in. Drill chuck: 1/16 in. to 5/8 in. Arbor: JT-33 Spindle travel: 3-1/4 in. Range of speeds: 550 RPM to 3470 RPM
This is an original vintage print advertisement, not a reproduction. Description/Advertiser: This is a single page ad from a vintage magazine. Shopmaster Year: 1956 Dimensions: Approximately 6 inches x 4.5 inches Condition: Very good Each vintage ad is packaged with a cardboard back insert with a protective PVC free plastic sleeve and shipped flat. Grab this rare vintage original advertisement for a trip down memory lane. A unique gift for someone special or yourself. Perfect for office or home. Ready to frame and be admired! Visit my Etsy shop for more vintage paper ads and other ephemera: KristensVintagePaper.etsy.com See more than one item you'd like to buy? Contact me as I will combine shipping for you to save you money. I want to ensure satisfaction with every one of my customers. If the merchandise you bought is unsatisfactory in any way, please contact me to arrange a refund. Customer satisfaction is a huge priority for me. Thanks for visiting!
Radial Bristle Disc, Bristle Type Type C, Product Type Radial Bristle Disc, Bristle Material Ceramic, Brush Dia. 2 in, Grit Not Applicable, Face Width 3/8 in, Bristle Diameter 2 in, Bristle Length Not Applicable, Compatible Tool Type Die Grinder, Drill Press, Pencil Grinder, Straight Grinder, Primary Material Application Aluminum, Brass, Bronze, Carbon Steel, Cast Iron, Stainless Steel, Connector Type Unthreaded Hole, Connector Size 3/8 in, Operating Speed - Maximum 20,000 RPM, Color Yellow
G9969 45" Radial Drill PressA popular drill press for both wood and metalworking shops that have bulky projects.The swing on the G9969 45" Radial Drill Press is a huge 45" (you can drill in the middle of a 45" diameter piece).For added adjustability, the headstock can be rotated 360° around the column, can swivel 360°
Gear up for the Ultimate Performance with the Powermatic PM2820EVS Drill Press. The gear-driven power transfers torque consistently and efficiently for any project in a wide range of materials. A removable cast table with 45-degree rotation has capacity for projects large and small. The high-visibility laser pinpoints the drilling location for total accuracy. Included fence and stop help make repeat and production drilling efficient. Handles can be moved to right or left for ease of use. Oversized cast base give this drill press stability. Integrated LED light reduces shadows for project visibility."}},"base-catalog-203293723":{"__typename":"BaseProduct Mechanical variable speed allows for full range of speeds with no belt changes 6 of quill travel with 1 revolution of the handle Fence system adjustable for a perfect 90° relationship to the table and for rapid alignment of stock Adjustable material stop makes repetitive actions accurate and quick Digital RPM readout allows user to optimize the spindle speed to the application Laser guides provide an accurate indication for tool point Includes 5/8 in. keyed chuck Reversible handles can be mounted on either side of the machine for more comfortable working of the quill 2 independently adjustable LED work lights eliminates shadows Work table can be rotated to a full 90° position
Have a question? Ask owners.Have a question about this? Ask people who own it. Start typing and see existing answers.Learn more Instant Answers Start typing and we'll see if it was already asked and answered. If there aren't already some matches, submit a new question. You'll get fast answers from customers who really own the item(s) and from our product experts. (About half the time you'll get an answer in under 2 hours!) Good Topics To Ask About Which items will best meet your needs What customers who own an item think of it How to use, fix, or take care of an item Product information General advice related to the types of products we sell Our store policies Customer Support For questions about an order you have placed, please contact customer support directly.
Take your drill press to the next level by building this simple drill press table. Step by step instructions are in this article!
This 5-speed floor model radial drill press features variable swing up to 34\" and pivoting heads for drilling at just about any angle. Truly versatile!
SHOP FOX® offers a broad assortment of drill presses to suit every need—from small hobby shops to professional machine shops. Our unique oscillating models provide the convenience of two machines in half the space, and our radial drill presses offer unmatched versatility. For the best selection of features, performance
The Shop Fox W1669 34" Benchtop Radial Drill Press boasts a 1/2 HP motor that smoothly powers the five spindle speeds ranging from 550 to 3000 RPM. The headstock can be tilted 45° left, 90° right, and slid forward or backward over the column allowing you full adjustability. To make sure that you get the best use of the 9-3/4" diameter table. The drill press features rack-and-pinion elevation controls-adjustable 9-1/2" vertically, 90° tilt (left and right) and is capable of 360° rotation around the column. The W1669 can easily drill holes through plastic, fiberglass, and composites, and has a maximum capacity to drill through a half inch of steel without bogging down. The JT33 keyed drill chuck is fitted to the JT-33 spindle taper and offers up to 3-1/4" of travel. The chuck accepts drill bits from 1/16" to 5/8". You can set the adjustable threaded depth stop for predetermined and repeatable drilling."}},"base-catalog-309625965":{"__typename":"BaseProduct Equipped with a heavy duty 1/4 HP induction motor for long lasting performance Features 5 speed selections for various drilling applications Outfitted with a locking depth stop for repetitive applications Chuck key storage for easy organization EXACTLINE Laser Alignment System conveniently marks the target area Integrated worklight for convenient use 7-5/8 in. x 6-1/2 in. table swivels 360 degree , tilts up to 45 degree , and is height-adjustable for a variety of drilling applications 3-year manufacturer's warranty Includes: (1) DP103L 10 in. Drill Press with EXACTLINE Laser Alignment System, (1) hex wrench, (1) chuck key, and operator's manual
Rikon's 34” Benchtop Radial Drill Press - Model: 30-140, provides great versatility for drilling of projects that are not so large as to require a floor model. This space-saving, portable size machine has proven to be quite valuable for solving unusual drilling needs on the jobsite – from drilling balustrades for stair railings, to timber framing hole & peg construction. Features: Powerful 1/3 HP Motor 5 Spindle Speeds - Versatile speed range for drilling into any type of material Clutch Depth Stop - Set your drill depth easily and accurately; great for repeatable drilling Rack and Pinion Table Height - Adjusting table height is easy with the turn of a handle Cast iron table Five-Year Warranty Specifications: Motor: 1/3 HP TEFC, 120V, 60Hz, 5.5A Motor RPM: 1,720 Swing: 34" Chuck Size: 5/8" Drilling Capacity: 5/8" Spindle Travel: 3-1/8" Spindle Taper: MT2 Head Rotates: 360° Head Tilt: 45° R, 90° L Speeds: 5 Speed Range: 620-3,100 Quill Diameter: 2-3/16" Table: 7-3/4" x 7-3/4" Table Tilts: 90° Table Rotates: 360° Maximum Chuck to Table: 10-3/4" Maximum Chuck to Base: 15-1/4" Column Diameter: 2-5/16" Overall Size: 37" H Overall Base Size: 13-3/4" x 8-1/2" Net Weight: 84 lb. Shipping Weight: 105 lb. What's Included: (1) Rikon® 34" Bench Top Radial Drill Press - 1/3 HP Notes: Due to shipping weight of 105 lb. an additional $55 fee for excess weight will be applied at checkout. Package will be brought to the back of the delivery truck for you to unload. See 'Ships Direct from Manufacturer' for warranty and return details. Shipping / Billing Information This product ships direct from the manufacturer: Your order will ship in approximately 7-21 business days. This product is considered special order. Your account will be charged when you place your order. Residential delivery fee applies for all LTL items. Express or overnight shipping is not available for this product. Ships by Ground to the 48 contiguous states. Cannot ship to Alaska, Hawaii, PO Boxes, APOs, US Territories, Canada or other foreign countries. Return Information If you have a return issue, contact Woodcraft Supply customer service @ 1-800-535-4482 for return details. Customer pays return freight. When returning product, please include the invoice number or customer number and refer to the back of the invoice for shipping instructions. If purchased at a Woodcraft Store, please return the item directly to the store where your purchase was made. To be eligible for credit for returned Rikon goods, customers must comply with each of the following requirements: Written authorization to return any products must be obtained from the RIKON Power Tools Customer Service Department before the products are returned. RIKON Power Tools will issue a Return Goods Authorization Number (RGA#), which must be clearly marked on the shipping label and bill of lading with the returned goods. RIKON Power Tools Will Not Accept Any Unauthorized Returns. A 15% restock fee will apply. Warranty Information Rikon offers a 5 year warranty.Customers with warranty claims, defective or damaged goods should contact RIKON Power Tools before returning any product to the distributor. RIKON Power Tools reserves the right to ship parts to effect repairs or replace product, whichever they may deem appropriate. Request to return defective or damaged goods by distributors must be submitted to RIKON Power Tools and will be reviewed for product misuse, abuse, negligence, accidents, repairs, alterations, lack of maintenance or normal wear and tear before giving authorization to return said goods. Defective/Damaged goods that are returned to RIKON Power Tools and show misuse, abuse, negligence, accidents, repairs, alterations, lack of maintenance or normal wear and tear are subject to a restocking charge equal to 15% of the credit given for the returned goods or $25.00, whichever is greater.
A drill press is a simple, one-job tool, right? Some might even call it “boring.” But as is often the case with tools, many tinkering minds have come up with clever ways to use this humble shop staple. Here’s how to use your drill press to its full potential.
W1670 34" Floor Radial Drill Press A tilting head benchtop drill press for adjustable angled drilling. The Shop Fox W1670 34" Floor Radial Drill Press boasts a 1/2 HP motor that smoothly powers the five spindle speeds ranging from 550 to 3000 RPM. The headstock can be tilted 45° left, 90° right, and slid forward or backward over the column allowing you full adjustability. To make sure that you get the best use of the 9-3/4" diameter table. The drill press features rack-and-pinion elevation controls—adjustable 24-1/2" vertically, 90° tilt (left and right), and is capable of 360° rotation around the column. The W1670 can easily drill holes through plastic, fiberglass, and composites, and has a maximum capacity to drill through a half inch of steel without bogging down. The JT33 keyed drill chuck is fitted to the JT-33 spindle taper and offers up to 3-1/4" of travel. The chuck accepts drill bits from 1/16" to 5/8". You can set the adjustable threaded depth stop for predetermined and repeatable drilling. The W1670 manual was written by our U.S. based Technical Documentation Department and is packed with useful information. The complete and easy-to-read manual makes it easier to assemble and maintain your drill press. Made in an ISO 9001 Factory CSA certified SPECIFICATIONS: Motor: 1/2 HP, single-phase, 120V, 4.7A Swing: 34" Drill chuck: 1/16"–5/8" Drilling capacity: 1/2" mild steel Spindle taper: JT-33 Spindle travel: 3-1/4" Number of speeds: 5, 550–3000 RPM Column diameter: 2.79" Table size: 9-3/4" dia. Table swing: 360° Table tilts: 90° L/R Table T-slots: 5 @ 5/8" Head tilt: 45° L, 90° R Footprint: 11" x 11" Overall size: 14" W x 32" D x 64-1/2" H Approximate shipping weight: 147 lbs. FEATURES: Two-year warranty!! Horizontal sliding headstock Threaded depth stop Table has lock levers Cushioned grip quill handles Crank handle operated rack-and-pinion vertical table movement Radial design allows angle drilling Precision-ground cast-iron table Need help? We offer U.S.-based customer service and technical support to get your questions answered and help keep your equipment running in top condition.
Features Are you in the market for a large radial drill for you fabrication shop? Does it have to have a really y large swing? Then the RD-1600H hydraulic radial drill press is for you. This press has a 5. 25hp motor that is powered by 220 volt three phase power. 2" maximum drilling capacity Heavy duty construction Pow
The WEN 17-Inch Twelve-Speed Floor Standing Drill Press meets the needs of both home and professional users. This model includes a full 4-3/4 inches of stroke capacity, allowing users a large enough spindle travel to easily drill through a 4x4 board. Adjust the speed to 12 different stops between 150 to 2940 RPM (150, 290, 320, 400, 520, 560, 1000, 1240, 1520, 1720, 2150, and 3150 RPM). The 14-inch by 14-inch cast iron table features a one-inch coolant runoff channel around the outer lip of the table to prevent both the workpieces and the drill bits from overheating. The table also pivots up to 45 degrees in both directions and can be positioned up to 26 inches away from the chuck to accommodate even the largest of workpieces. The laser pointer ensures maximum precision during drilling operations, creating an X through the center of your target. The JT3 chuck accepts bits anywhere from 1/16 to 5/8 inches in size with onboard key storage to make sure that the chuck key is always close by. Cast iron frame and base gives the machine a hefty support system to prevent the drill press from walking or vibrating during operation. This beast measures in at 30 by 14 by 67 inches in size with a weight of 214 pounds. And because it is a WEN product, the WEN 17-inch 13-Amp Twelve-Speed Floor Standing Drill Press comes backed by a 2-year warranty, a stocked inventory of replacement parts, and a friendly customer service team."}},"base-catalog-205769834":{"__typename":"BaseProduct 4 in. spindle travel makes drilling through 4 x 4 boards easier than ever Infinitely adjust the variable speed anywhere from 280 RPM to 3300 RPM Includes a built-in work light, a precision laser, a 5/8 in. chuck and onboard chuck key storage Cast iron work table pivots up to 45° in both directions Backed by a 2-year warranty, a friendly customer service line and a nationwide network of skilled technicians
Rikon's 34” Floor Radial Drill Press - Model: 30-251, has the same great features as the bench model, but has larger components in proportion with the added height and capacities of this floor model – larger base, column, and table assemblies. This drill press is good for drilling holes in large items and workpieces. The work table on this model is round shape, and will turn 360° as well as tilt 45° in left and right. Features: Powerful 1/3 HP Motor 5 Spindle Speeds Clutch Depth Stop Cast Iron Table (Round) Large Cast Iron Feed Handles Specifications: Motor: 1/3 HP TEFC, 120V,60Hz, 5.5A RPM: 1,720 Swing: 34" Chuck Size: 5/8" Chuck Taper: JT3 Drilling Capacity: 5/8" Spindle Travel: 3-1/8" Spindle Taper: MT2 Head Rotates: 360° Head Tilts: 45° Right, 90° Left Speeds: 5 Speed Range (RPM): 620 – 3,100 Quill Diameter: 2-3/16" Table: 11-3/16" Table Tilts: 90° Table Rotates: 360° Maximum Chuck to Table: 28-3/8" Maximum Chuck to Base: 47-3/4" Column Diameter: 2-7/8" Overall Size: 64" H Overall Base Size: 18" x 10-1/2" Net Weight: 120 lb. What's Included: (1) Rikon® 34" Floor Radial Drill Press - 1/3 HP Shipping / Billing Information This product ships direct from the manufacturer: Your order will ship in approximately 7-21 business days. This product is considered special order. Your account will be charged when you place your order. Residential delivery fee applies for all LTL items. Express or overnight shipping is not available for this product. Ships by Ground to the 48 contiguous states. Cannot ship to Alaska, Hawaii, PO Boxes, APOs, US Territories, Canada or other foreign countries. Return Information If you have a return issue, contact Woodcraft Supply customer service @ 1-800-535-4482 for return details. Customer pays return freight. When returning product, please include the invoice number or customer number and refer to the back of the invoice for shipping instructions. If purchased at a Woodcraft Store, please return the item directly to the store where your purchase was made. To be eligible for credit for returned Rikon goods, customers must comply with each of the following requirements: Written authorization to return any products must be obtained from the RIKON Power Tools Customer Service Department before the products are returned. RIKON Power Tools will issue a Return Goods Authorization Number (RGA#), which must be clearly marked on the shipping label and bill of lading with the returned goods. RIKON Power Tools Will Not Accept Any Unauthorized Returns. A 15% restock fee will apply. Warranty Information Rikon offers a 5 year warranty.Customers with warranty claims, defective or damaged goods should contact RIKON Power Tools before returning any product to the distributor. RIKON Power Tools reserves the right to ship parts to effect repairs or replace product, whichever they may deem appropriate. Request to return defective or damaged goods by distributors must be submitted to RIKON Power Tools and will be reviewed for product misuse, abuse, negligence, accidents, repairs, alterations, lack of maintenance or normal wear and tear before giving authorization to return said goods. Defective/Damaged goods that are returned to RIKON Power Tools and show misuse, abuse, negligence, accidents, repairs, alterations, lack of maintenance or normal wear and tear are subject to a restocking charge equal to 15% of the credit given for the returned goods or $25.00, whichever is greater.
John concludes his drill press table build by sharing a few add-ons that can make your time at the drill press easier. This handful of accessories are useful on any drill press table that you have.
The powerful 1/2 HP motor with variable speeds (550-3000 RPM) handles a wide range of drilling tasks in various materials; The tilting headstock and sliding action allows for drilling at precise angles and on angled workpieces. A JT33 keyed drill chuck with 3-1/4" travel and 1/16" to 5/8" bit capacity ensures accurate drilling for various hole sizes; Adjustable threaded depth stop allows for consistent drilling depths for repetitive tasks and precise woodworking projects. A large 9-3/4" diameter table with 9-1/2 inches of adjustability and 360° rotation offers exceptional flexibility for handling different project sizes and shapes; Backed by a 2-year warranty.
SHOP FOX® offers a broad assortment of drill presses to suit every need—from small hobby shops to professional machine shops. Our unique oscillating models provide the convenience of two machines in half the space, and our radial drill presses offer unmatched versatility. For the best selection of features, performance
G7945 34" Benchtop Radial Drill Press An award-winning and truly versatile benchtop drill press. The G7945 34" Benchtop Radial Drill Press was named as one of the Best Drill Presses for Contractors or DIY Projects by Tool Digest. Boasting a powerful 1/2 HP motor, the G7945 smoothly powers the five spindle speeds ranging from 550 to 3000 RPM. The headstock can be tilted 90° right, 45° left, and slid forward or backward over the column allowing you full adjustability. To make sure that you get the best use of the table, the drill press features rack-and-pinion elevation controls — adjustable 24-1/2" vertically, 90° tilt (left and right), and is capable of 360° rotation around the column. The JT33 keyed drill chuck is fitted to the JT-33 spindle taper and offers up to 3-1/4" of travel and a colossal 14" of swing. The chuck accepts drill bits from 1/16" to 5/8". You can set the adjustable threaded depth stop for predetermined and repeatable drilling. The G7945 can easily drill holes through fiberglass, plastic, and composites and has a maximum capacity to drill through a half inch of steel without bogging down. With heavy duty power and a massive amount of working area, the G7945 will eat the vast majority of projects without complaint. The G7945 manual was written by our U.S.-based Technical Documentation Department and is packed with useful information. The complete and easy-to-read manual makes it easier to assemble and maintain your drill press. Made in an ISO 9001 Factory CSA certified SPECIFICATIONS: Motor: 1/2 HP, single-phase, 120V, 4.7A Swing: 34" Spindle taper: JT-33 Spindle travel: 3-1/4" Spindle speeds: 5, 550–3000 RPM Drill chuck: 1/16"–5/8" Drilling capacity: 1/2" mild steel Maximum distance from spindle to table: 12-3/4" Table size: 8-5/8" x 9" Table swivel around center: 360° Table swivel around column: 360° Table tilt: 90° L/R Table T-slot size: 5/8" Head tilt: 45° left, 90° right Head swivel: 360° Column diameter: 2.36" Footprint: 13-1/2" x 8-1/2" Overall size: 11-1/2" W x 33-1/2" D x 31-1/2" H Approximate shipping weight: 97 lbs. FEATURES Precision-ground cast-iron table Threaded depth stop Crank handle operated rack-and-pinion vertical table movement Table has lock levers Radial design allows angle drilling Cushioned grip quill handles 1-year limited warranty Need help? We offer U.S.-based customer service and technical support to get your questions answered and help keep your equipment running in top condition.
Some materials and woodworking tasks can generate clouds of dust. Keep the dust out the air and off the floor in your shop with these handy, shop-made collectors.
My router table is probably the most-used tool in my shop. I have dust collector ports on the fence, but when I rout with a bearing-guided bit, it still makes a huge mess. One day I was at my local…
Benchtop mortising machines aren’t the only option when it comes to cutting square-shouldered mortises. A drill-press mortising attachment can be just as effective and it costs a lot less.