In this tutorial we design a system to read the RFID cards using MSP430 launchpad and EM-18 RFID Reader.
Here we make a line follower robot using MSP430 launchpad from Texas Instruments, which follows the black line.
In this tutorial we interface Bluetooth module HC-05 with MSP430 Launchpad from Texas Instruments. In this interfacing example, we will control on-board LED of MSP430 from the smart phone by using an Bluetooth Terminal android application.
In this project we are using MSP430 launchpad and a vibration sensor to detect vehicle accident and track the vehicle using GPS module.
In this tutorial we will make a Digital Clock by interfacing RTC module DS3231 with MSP430 and display the time and date on 16x2 LCD.
In this tutorial we will learn how to use ADC in MSP430G2 to read Analog voltages using the Energia IDE. We will interface a small potentiometer to MSP board and supply a varying voltage to an Analog pin, read the voltage and display it on the Serial Monitor.
In this tutorial we have programmed MSP430 using Code Composer Studio CCS to interface it with 16x2 LCD display.
In this tutorial we will Interface Stepper Motor using MSP430. The MSP-EXP430G2 is a Development Tool a.k.a LaunchPad provided by the Texas Instruments to learn and practice on how to use their Microcontrollers.
In this tutorial we will learn about Code Composer Studio and how it is used to program MSP430. This tutorial is written for very beginners and no hardware is required except the MSP430 board and a computer.
In this tutorial, we have used the external interrupts on MSP430 to toggle different LEDs. When an external interrupt is given by the change of state using a push-button, the control is transferred (pre-empted) to the ISR and it does the needful.
In this series of tutorials, we will learn about this MSP430G2 LaunchPad and how to program it. Using this LaunchPad we can work with MSP430 Microcontrollers which offers 16-bit performance with an operational speed up to 16MHz.
In this tutorial we are interfacing 16x2 LCD with MSP430 launchpad. The Energia IDE provides a beautiful library which makes the interfacing a piece of cake and hence it’s not mandatory to know anything about the display module.
Back to Spec Sheets MSP430: Using a Launchpad board Rev 1.5 for this exercise. This one came with a 2553. Using Energia for the TI ...
Block Programming With MSP430 Launchpad: This instructables shows how to use Ardublock graphical program with MSP430 Launchpad, a low cost Arduino like microcontroller. Designing robot is challenging having to learn about electronic components, circuit diagram, bread boarding and comp…
The most used communication protocols are USART, IIC, SPI and CAN. Each communication protocol has its own advantage and disadvantage. Let’s focus on the I2C part for now and learn using I2C protocol in MSP430 Launchpad.
In this section we will learn how to configure and use the ADC10 of MSP430G2XX3 microcontroller that comes with the TI Launchpad development board. Later we will configure the internal temperature sensor of MSP430 and display the value on a 16X2 LCD module. MSP430G2xxxx series (for eg MSP430G2553) comes with a 10 bit Successive Approximation ADC that can operate at 200Ksps.
Controlling DC Motors Using MSP430 Launchpad: Hello Folks, In this Instructable we are going to Control two DC Motors using MSP430 Launchpad and L293D Motor Control Chip. The original article is available online here Here we are using a Motor Control Booster Pack (or shield) for MSP430 Launchpa…
MSP430 Based Chronulator (using Launchpad Chip): Recently, I have been experimenting with microcontrollers. A project that really caught my eye was the Chronulator at http://www.sharebrained.com. At the same time, Texas Instruments released an experimenter's kit called the Launchpad for the outsta…
Blog dedicated to DIY digital readout TouchDRO and other hobby machining and engineering subjects.
Here we create a demo IoT project where we use ESP8266 and MSP430 Launchpad to send an email upon fire detection.
