Smarter Shopping, Better Living! Aliexpress.com
How to Control Tracked Robot Via Joystick NRF24L01 Module Arduino Part2 Rx: The instruction "How to control Tracked Robot via Joystick NRF24L01 Module Arduino Part2 Rx" will describe the method how to build Receiver(Rx) on Tracked Robot for Transmitter(Tx) in the instruction "How to control Tracked Robot via Joystick NRF24L…
This is a short guide of the Skyline 32 flight controller for people who are new to the board. The Skyline 32 flight controller is the equivalent to the Naze32+ and is designed by Emax for the Nighthawk series. You can t…
See how small ButtonDuino is! Only 18mm x 18mm
Erik Kettenburg is raising funds for Digispark Pro - tiny, Arduino ready, mobile & usb dev board! on Kickstarter! The tiny Arduino IDE ready, usb and mobile dev board and ecosystem - cheap enough to leave in any project! Wi-fi, BLE, and 25+ shields!
Arduino Mini 2.4GHz and IR Remote Control System: This is my DIY remote control system. It was designed during the last couple of months. It's based on an Atmega 328P MCU and NRF24L01+ radio modules. The software and board CAD data are available on my GitHub repo: https://github.com/TheDIYGuy999 …
JDM2 Based PIC Programmer: Schematic & layout for an updated JDM2 PIC Programmer. Includes clock & data filter, Vpp voltage divider for modern PIC microcontrollers (eg USB PIC 18F2455/4455).Prior to reading sites like www.hackaday.com & www.makezine.com/blog I ha…
I2C Relay Board: Relays are one of the most common interfaces between a micro controller and the outside world. It provides electrical isolation between the low voltage circuits of the micro controller, and the loads. So why this funny I2C Relay Board, you might ask…
ESP32: DIY Motor Driver With ESP32 Controller: This is the simplest motor driver that could possibly be built using only one NPN transistor, which is controlled and driven by the ESP32 micro controller board.
A simple guide shows how to construct and use an HF antenna analyser using a Windows PC, micro-controller, and DDS evaluation board.
As long as you didn't damage the micro-controller, you still might be able to use your Arduino board. This post assumes that you have the sa...
BBC MIcrobit Bot Using the L9110 Motor Controller: I wanted to connect the BBC Microbit to a standard motor driver board like the L9110 or the L298N. The Micro Bit (also referred to as BBC Micro Bit, stylized as micro:bit) is an ARM-based embedded system designed by the BBC for use in computer educa…
How to Program the ATtiny85 With the Arduino Uno Board: In this tutorial we will use an Arduino board as an ATtiny programmer. To do this we will use one Arduino UNO board as an ISP (programmer) and one ATtiny85 micro-controller. We will use Codebender - online Arduino IDE. With the following procedure…
3D Printed USB Flight Controller / Joystick With Four Axes: With the new flight simulator coming out fall 2020, it is about time to make your own JOYSTICK! This is a 3D printed fully functional flight control joystick. The usb interface is managed by an Arduino Micro (or compatible board). The axes movemen…
Wifi Switch Board or Smart Plug With Esp8266, Attiny 85 & PIR Sensor With Android App: The Wifi Arduino 85 is a small board with ESP8266 -01 module, Attiny85 micro controller and a relay. It Also has and additional header for connecting an external relay or to connect sensors like PIR, IR etc depending on your application. If you are…
Turn a Commodore 64 Into an IOS Bluetooth Keyboard: This instructable describes how to turn a Commodore 64 computer into a bluetooth keyboard. It involves programming a micro controller with the Arduino IDE and constructing a circuit board. Supplies you'll need (some are optional): Commodore 64 w…
The bare STM32F103 board only comes with a default USART boot loader. Even though there is a USB port on the board, you cannot use it to program it because it does not have the relevant bootloader.I got my board for less than $2 from Advanced Tech on AliExpress. We need to use a simple USB to UART converter to program the board via USART with a USB boot loader, and then we can get back to programming it directly via USB.First, connect your USB to Serial/UART/TTL Converter like this:(http://www.wifi4things.com/stm32f103c8t6-blue-pill-board-with-arduino-ide-on-linux/)In the image above, you see two yellow jumpers marked BOOT0 and BOOT1. These specify the source of code for the micro-controller. In the default state of both being 0, the micro-controller uses its own flash memory bootloader — which there is none right now — and which we are adding. For now, to be able to program the micro using USART, you need to set BOOT0 as 1 and leave BOOT1to 0. Basically move the first jumper and leave the second one.Now, download the stm32loader python script and run it to see that all the necessary dependencies are satisfied. I had to pip install pyserial
PRICES MAY VARY. 3 ft. Hd cable; 6 ft. Micro cable with AC adapter Upscale to 720p HD with 4: 3/16: 9 aspect Ratio button; supports 2600 cartridges and original joysticks and paddles On-board: mode select, Color change (Color/B&W), and save states; Two (2) Controller ports with one (1) Premium Controller packed in (10 ft. Cable) Included memory card slot (and memory card) for homebrew testing and firmware updates
Arduino Password Security System With Magnetic Door Sensors: In this Instructables guide I will show you how to make your own password security system by using the Arduino uno board and some magnetic door switches. I made my own circuit by using the ATmega328 micro controller but this is an optional step. In …
Arduino Password Unlock Door Security System: Hello! In this Instructables guide I will show you how to make your own password unlock door system by using the Arduino uno board. I made my own circuit by using the ATmega328 micro controller but this is an optional step. In this guide I will help…
