Der Digispark ist wohl einer der kompaktesten und kleinsten Mikrocontroller, die es aktuell gibt. Der AZ-Delivery Digispark mit ATTiny85 verfügt über einen USB-Stecker direkt on-Board und kann ohne weiteres Kabel direkt mit einem USB-Anschluss verbunden werden. Der integrierte ATTiny85 wird direkt über den USB-Anschluss mit Spannung versorgt. Außerdem besitzt der Digispark 6 freiprogrammierbare GPIO Anschlüsse, die mit der bekannten Arduino-IDE Programmierumgebung programmiert werden können. Für die eigenen Programme stehen 8kB Speicher zur Verfügung. Neben den 3 weiteren Pins auf der Platine, die für eine Externe Spannungsversorgung genutzt werden können, unterstützt der ATTiny85 volle SPI und I2C Schnittstellen. Besonderheiten On-Board USB zur einfachen Programmierung durch direktes Einstecken in den PC oder mit einem üblichen USB-Verlängerungskabel. Der hochleistungsfähige und stromsparende 8-Bit Mikrocontroller-Chip eignet sich perfekt für jede Art von Projekten. 8kB systeminterner programmierbarer Flash-Speicher zur Programmspeicherung. Kompatible und zuverlässige Verbindung. Technische Daten Abmessungen 20 x 19 x 6mm (0.8x0.7x0.2in) Betriebsspannung 2,7V - 5,5V Externe Versorgungsspannung 6V - 12V (VIN-Pin) Betriebstemperatur -40°C bis 85°C Eingangs-/Ausgangsstifte 6 Mehrzweckstifte (analog, digital) Schnittstelle SPI, I2C Speicherplatz 8kB Geringer Stromverbrauch aktiver Modus: 1MHz - 1,8V, 300uA Power-Down-Modus: 0,1uA bei 1,8V Hohe Leistung - geringer Stromverbrauch Unser DigiSpark Modul ist mit einem leistungsstarken 8-Bit-Mikrocontroller ausgestattet, der trotz der hohen Leistung wenig Strom verbraucht. Quick-Start-Guide Beim Kauf eines unserer hochwertigen Produkte erhalten Sie zusätzlich ein inklusives E-Book für einen schnellen Einstieg in die Welt der Mikroelektronik.
Temperature-Humidity Monitoring Using Digispark USB and RGB Led: Digispark USB is an ATTINY85 powered tiny development board with on board USB plug in and compatible with Arduino IDE. You must install and set some required stuffs. Now, i want to introduce a minimalist but functional circuit for monitoring Tempera…
Temperature-Humidity Monitoring Using Digispark USB and RGB Led: Digispark USB is an ATTINY85 powered tiny development board with on board USB plug in and compatible with Arduino IDE. You must install and set some required stuffs. Now, i want to introduce a minimalist but functional circuit for monitoring Tempera…
In this illustration we will going to wire the Digispark ATTiny Development Board with HC-SR04 Ultrasonic range detector, as our output we will going to use an RGB LED when the objects is near or closer to the sensor the RGB LED will going to switch on and if it is out of range the
Hey guys, welcome back, In the previous post, I told you how an IR sensor works, how to make a line follower using an IR sensor and to make a Simple DIY Burglar Alarm using an IR sensor and a Buzzer without using any micro controller or complicated coding. More info
I've been using Digispark for wearable projects lately because of its small size and low cost. The clones I've been using have a built-in MicroUSB port which is convenient for both programming and powering the boards. I had the opportunity...
In this project, we are going to make a USB IR remote receiver that will act as a keyboard using Digispark Attiny85 to control the functions of the media
For one of my hobby projects, I needed to add a small countdown timer at an affordable cost. Fortunately, a DigiSpark Attiny85 development board was lying
Neste post mostramos como usar a placa Digispark ATtiny85 com display LCD 16x2 I2C e sensor de temperatura DHT11. Confira!
Picoduino Password Keeper (PPK): This is a password auto typer based on Picoduino. Picoduino is an Attiny85 board, similar to digispark but it has a couple of bells and whistles. For example it has a pushbutton which can be used as reset or (in our case) a user input button, and an…
Sure, countless microcontroller development boards featuring a USB connection have made it to the Projects and Tutorials pages of Electroschematics.
Veja neste tutorial como utilizar uma placa de desenvolvimento Digispark ATtiny85 com display OLED I2C e mostrar na tela o que você quiser. Confira!
A thermostat with an OLED capable of plugging into a USB port.
De digispark is het onofficiele broertje van de Arduino, welke via kickstarter de wereld in is geholpen. Dit kleine bordje bevat slechts een voltage regulator en een Attiny85 als microcontroller. Deze module kan direct in een computer worden geplugd en worden geprogrammeerd met de Arduino IDE, er is geen losse programmer noodzakelijk.
Programming ATtiny85 IC directly through USB using Digispark Bootloader
How to Unlock Digispark ATtiny85 and Convert It to a Trinket: Digispark ATtiny85 boards come with the Micronucleus bootloader and with the reset pin disabled. When reset is disabled you get an additional digital pin, and you must upload sketches using the bootloader. You may not use ISP programming. There ar…
In this project, we are going to make a USB IR remote receiver that will act as a keyboard using Digispark Attiny85 to control the functions of the media
I've been using Digispark for wearable projects lately because of its small size and low cost. The clones I've been using have a built-in MicroUSB port which is convenient for both programming and powering the boards. I had the opportunity...
The Digispark is a tiny, Arduino compatible development board using the ATMEL ATtiny85 microcontroller. It has its own USB bootloader and built in USB capability, allowing you to program it with the Arduino SDK and also use it as native USB device.It is similar to the Arduino line, only cheaper, smaller, and a bit less powerful.With the ability to use the familiar Arduino IDE, the Digispark is a great way to jump into electronics, or perfect for when an Arduino is too big or too much.Features:Support for the Arduino IDE 1.0+ (OSX/Win/Linux).Power via USB or External Source - 5V or 7-16V (12v or less recommended, automatic selection).On-board 500ma 5V Regulator.Built-in USB (and serial debugging).6 I/O Pins (2 are used for USB only if your program actively communicates over USB, otherwise you can use all 6 even if you are programming via USB).8k Flash Memory (about 6k after bootloader).I2C and SPI (vis USI).PWM on 3 pins (more possible with Software PWM).ADC on 4 pins.Power LED and Test/Status LEDSize: 18.5mm x 26mm including USB connector, 18.5mm x 17mm excluding connector.The ATMEL ATtiny85 datasheet can be viewed or downloaded here: ATMEL ATtiny85 datasheet (PDF) Package Includes:1 x Digispark Kickstarter Attiny85 USB Development Board for Arduino with connector pins Link to online Specifications and usage documentation
Digispark is the Attiny85-based USB development board from Digistump. Due to the built-in USB connector, you can directly program the Attiny85 using Arduino
Recently I came to understand the true demand for a multi-purpose digital pulse counter. So I designed an east-to-build digital pulse counter circuit based on some generally available cheap electronic components. The quick microcontroller based […]
How to Unlock Digispark ATtiny85 and Convert It to a Trinket: Digispark ATtiny85 boards come with the Micronucleus bootloader and with the reset pin disabled. When reset is disabled you get an additional digital pin, and you must upload sketches using the bootloader. You may not use ISP programming. There ar…
Programming ATtiny85 IC directly through USB using Digispark Bootloader
После изучения платформы Arduino на базе Uno и обзора множества носимых устройств, захотелось освоить мир компактных контроллеров и модулей, которым не нужны блок питания, макетка, куча проводов и…
Digispark DIY: the Smallest USB Arduino: Digispark is an ATtiny85 based microcontroller development board come with USB interface. Coding is similar to Arduino, and it use the familiar Arduino IDE for development. Digispark is copyrighted by Digistump LLC (digistump.com) and the full…
Paperduino Tiny: Build Arduino compatible board on piece of paper. Paperduino Tiny is very cheap and easy to build Arduino compatible board with USB and software compatible with Digispark board. Paperduino Tiny include an ATtiny85 microcontroller and come with USB…
USB NeoPixel Deco Lights (via Digispark / ATtiny85): For this Instructable we need a WS2812 LED strip, also known as NeoPixel, and any MCU that could be programmed via Arduino. I use Digispark, it is a very nice tiny MCU based on ATtiny85. It has a special bootloader called Micronucleus which provides…
How to Unlock Digispark ATtiny85 and Convert It to a Trinket: Digispark ATtiny85 boards come with the Micronucleus bootloader and with the reset pin disabled. When reset is disabled you get an additional digital pin, and you must upload sketches using the bootloader. You may not use ISP programming. There ar…
USB NeoPixel Deco Lights (via Digispark / ATtiny85): For this Instructable we need a WS2812 LED strip, also known as NeoPixel, and any MCU that could be programmed via Arduino. I use Digispark, it is a very nice tiny MCU based on ATtiny85. It has a special bootloader called Micronucleus which provides…
Don't cannibalize old projects for their brains! Give them immortality with this inexpensive chip – here's how.
Conheça e programe a Digispark ATtiny85 com IDE Arduino, uma placa de desenvolvimento compacta ideal para projetos de IoT (Internet of Things).
