Le droïde chercheur ID9 était un modèle de petit droïde chercheur fabriqué par les Industries Arakyd. La Septième Sœur, Inquisitrice sous l'Empire Galactique, possédait plusieurs de ces droïdes. Des droïdes chercheurs ID9 accompagnaient la Septième Sœur lors de ses missions, comme sur la station médicale de classe Haven où ils traquèrent et combattirent contre Sabine Wren, Garazed Orrelios, Ezra Bridger et Chopper. Leurs pinces pouvaient émettre une forte décharge électrique, capable de désactiv
If you need this printed please contact me for a quote. **These files are not for distribution or for selling kits/parts. Please read my Policies & FAQ before purchasing. Thank you for your support!** Heads up!!! This is very different from the new Battlefront 2 ID10 droid. Please make sure of which droid you need before purchasing! This the 3D model I created from scratch of the ID9 Seeker Droids the Seventh Sister uses. Here is a link to my blog post with some exploded views of him: http://keltaria.com/2017/11/id9-seeker-droid-seventh-sister/ This file contains ten (10) .STL files meant for 3D printers. Please read the points below before purchasing and contact me with any questions! =) Some points: - These files produce the basic parts for the droid. All his appendage segments are separate for you to pose him how you want. - XTC3D is awesome. I use that to smooth out a lot of my prints (but be careful applying it!). Go lightly and gradually to reduce drippage on curved parts. Coat & sand = so smooth! File off the bumps/drips. - The top and bottom of his eye-hole are the thinnest parts of the print, it may even be spotty depending on your print settings. With a coating of XTC3D and paint, it covers it up quite nicely. - There is an area for a basic tealight (I found remote control ones, they are kinda awesome!). If you are an electrical wizard then by all means use other types of lights/LEDs. - Attach the legs as you see fit. I used brass rods and superglue. - There are indentations for small magnets on the bottom piece and washers on the top (please note this is not as strong as I like it with what I'm currently using, BUT I'll be holding him from the bottom so I'm not too concerned). - I used an acrylic rod for his antenna and scrap ABS for his flag. Depending what you find it may fit right in the existing hole or file it open a bit. - Always be careful with your little droid. One good whack and the legs will likely still pop off/come loose. Please see the images for this listing for samples of the 3D files and how they are laid out for printing. I even provided extra hands/feet for other options! =) List of files: Droid Bottom HEAD v2.2 Droid Top HEAD v2.2 Droid Inner HEAD v2.2 Droid ARM A v2.2 Droid ARM B v2.2 Droid HANDS extra v2.2 Droid LEG A v2.2 Droid LEG B v2.2 Droid LEG C v2.2 Droid FEET extra v2.2
Spacebobs Droids has once again opened its Droid Division Workshop to bring you a super detailed and solid state ID-9 Animated Styled Seeker Probe Droid. Listing is NOT a physical item/prop, but it is, FILES for 3D PRINTING at home. As files cannot be returned to me... I cannot refund money anymore unfortunately, be very sure of this before buying. The Droid STL files include everything you need to print the whole Droid including a printable Stand, and Wall Mount! The files also include a PDF with instructions and pictures on how to complete the build and a short list of hardwares needed to make the Droid... For the Legs there are all printed versions, or there are Chicago Screw and Furniture Bolt joint versions as well. Standing at about 480mm tall over all, including the stand, it is smaller and simpler than the ID-10 styled version. The whole thing is in parts easily printable on an on a smaller printer like the Ender 3. As with all DD 3D files they are single person usage and not to be shared or sold, even if (especially if lol) modified. Make sure you save your original Link PDF from Etsy so you can re-access the Dropbox folders at a later date if needed. The Head features voids for lighting and channels for wires and such to all of the many light positions. It can be filled and finished to your own standard but even looks great printed at 0.3 layer height and left with the layer lines as it’s a robot. File downloaded will simply be a PDF with an introduction to the build which contains a link to the Droids most updated STL and Information Dropbox Files. Thank you and Happy Printing
The ID9 Seeker Droid (also referred as Parrot Droids) is a small Imperial probe droid that appears in the second season of Star Wars Rebels. They may be small in size, but ID9 seeker droids are dangerous and deadly when used for nefarious purposes. Resembling probe droids, ID9 seekers had a half-hemisphere dome with a threatening red eye. They could hover and crawl on their pincers, imitate other droids, and were outfitted with electro-shock prods that could incapacitate mechanical beings and ha