Our oldest daughter, Greta (10 this month!) has a real passion for horses. She's taking riding lessons and learning so much that I have a feeling our p ...
Our oldest daughter, Greta (10 this month!) has a real passion for horses. She's taking riding lessons and learning so much that I have a feeling our p ...
Have you ever seen a really pretty piece of canvas art in one of your favorite home store that you love, except for the weird finish on it? Or you're undecided on how you
This is a floater frame for a gallery wrapped canvas. It is called a "Floater" because the frame is built larger than the canvas and then the canvas is mounted inside the frame and attached by screws to the back of the frame. This leaves a gap between the frame edges and canvas and appears to make the canvas float inside of the frame. Very cool looking! You can buy these ready made or have them made per your dimensions if you look around online or talk to your local framer. Since my framing budget is nowhere near that of many painters whose names you know I made this one myself...it is my second floater frame I've made and came out pretty good I think. It is made of Red Oak strips bought at Home Depot, 1"x4". I then saw it down to the size I need on a table saw. The corners are miter-cut on the table saw and then glued and nailed together...it's sanded and then rubbed with wax to protect the wood and enhance the wood grain of the oak. Here is the procedure for those of you do-it-yourself types. Here is the Red Oak purchased at Home Depot before cutting down to lengths to work with. Cost is about $2.50 per foot. I then cut the length into 4 pieces. Then cut the width for the sides and back and then cut miter cuts where the 2 pieces will join at 90 degree angles. The miter cut is a 45 degree cut. The next step is to assemble the four sides of the frame with wood glue and either small finishing nails or brads. I used brads shot with an airgun (fast!) but a hammer and finishing nails would work fine. If you used an epoxy glue you could probably skip nailing altogether. I was working alone so having this little clamp to hold the corners is great! I should have bought two though. This is a crummy picture of the next step...nailing the back to the sides but you can see how the miter cut works. It gives you a nice joined edge That is the basic assembly. Let it dry overnight and then sand all the sides and edges. I sand a smooth radius around the front edges and corners too. After that you wipe it down to get the sawdust off of it and then start rubbing in the wax. I used a wax with an orange oil in it to protect the wood. I love this step because now the oak really shows it's beauty. Here is the whole frame waxed up....nice! From this point you just drill holes in the back of the frame and then place your painting in there...get the sides even and then screw into the back of your strecther bars to hold it all together. Here is the frame and painting mounted together. Here you can see the gap between frame and canvas. Also, the corners and edges. Notice the side nails are placed at bottom and top of frame so you can't see them. The back is nailed from behind so you can't see those nails either. It looks like a ton of work but this second frame was much easier to build than the first...all of the figuring out was spent on that first one. I've seen versions of framing paintings where they built the frame flush with the edges of the painting and made no back at all. I've seen one like that made that was simply built of pine and then sprayed with black paint and it looked pretty cool too. Just a matter of what results you are looking for. If you kept the edges all flat without the miter cuts and could find the wood in the correct thickness you could build this frame with just a miter box made of wood or plastic. It's just hard finding the wood in the right thickness. My wood is 3/8" thick and I started with 1" thick wood. That's why you need a table saw to do this. The table saw is also needed to cut the miter cuts. It's a fun project though....give it a try sometime. UPDATE.....here is a pic of the back of the frame showing how the canvas mounts to the frame. The canvas lays flat against the back of the frame. Your stretcher bars of the canvas will butt up against the back of the frame. All you need to do is center the canvas in the frame and drill a pilot hole through the back of the frame and into your stretcher bar. Then simply put a screw in to hold your canvas to the back of the frame. I used 4 screws to mount this painting. To center the painting I use either pieces of foam core or bits of old mat board placed between the frame and the edge of the canvas...just add pieces until the painting is even on all 4 sides. ANOTHER UPDATE....Here are some additional pics of the assembly of the frame. Again, the shape of the frame is an "L" for each side of the frame. I did a mitre cut on each piece where they are glued together forming the "L". A mitre cut is a 45 degree bevel cut (actually any degree of bevel). For additonal strength I shot 3/4" brads, which are like finishing nails, in from the back of the frame....see diagram below. Instead of brads you can use small finishing nails. I bought an air powered brad gun, which is a lot like an electric staple gun, at Harbor Freight for about $20. I already had a compressor to run it. I'm sure they sell manual or electric brad guns too....try Home Depot. Here you can see from the behind the frame looking down from the top. The brads (circled in white) are shot from the top and from behind the frame. This keeps the viewer from seeing the brads when the frame hangs on the wall. Brads at the bottom of the frame are shot upward...the reverse of these tops ones. You can also see the mounting sheet metal screw going through the back of the frame and into the back of the stretcher bar holding the painting to the frame. By shooting the brads from the top and back of the frame you end up with a smooth brad-free frame side like it is shown below. By using the bevelled mitre cut to join the sides and back you have a seamless joint.
Happy Spring everyone! I love this season, mostly for the incredible weather, but also because I love cleaning. I love to purge and redecorate, so there’s always a project going on at my hous…
This post contains affiliate links, if you make a purchase after clicking one of my links, I will receive a small portion of the sale at no additional cost to you. For my One Room Challenge Guest Room Project Reveal (check out all of my One Room Challenge Posts here), I showed off my 3 DIY paintings mounted in handmade oak frames. I completed my paintings to solve the challenge of filling one large bank wall and wanted my DIY abstract art to really shine so worked with my dad to build custom canvas float frames. Float frames are different from regular frames meant for canvas because they are made to be just a little bit bigger than the canvas itself. While a regular canvas frame would hug tight against the canvas, a float frame has an intentional gap all the way around to make the canvas look like it’s floating inside the frame. Before I get into the how-to of it all, lemme show you what one of these frames looks like IRL. How to Make a Wooden Canvas Float Frame I’m going to walk you step by step through the process of making your own float frame for canvas art. […]
Our oldest daughter, Greta (10 this month!) has a real passion for horses. She's taking riding lessons and learning so much that I have a feeling our p ...
Our oldest daughter, Greta (10 this month!) has a real passion for horses. She's taking riding lessons and learning so much that I have a feeling our p ...
Our oldest daughter, Greta (10 this month!) has a real passion for horses. She's taking riding lessons and learning so much that I have a feeling our p ...
How to make DIY floater frames for artwork on shallow canvas panels.
Do you have a lot of Plein Air paintings in your studio, and you want to give them nice frames on a budget? Well, look no further. Here is h...
I think that the Float Frame (or floater or floating frame as I’ve heard them called) is a particularly stylish way to display canvas art from paintings to canvas photo prints (also check out…
Do you have artwork that needs framed but you aren't willing to pay a ton of money for a custom frame? Follow this easy tutorial and do it yourself!
