This cream dress was made about 13 years ago and it hangs in my dolls shabby chic apartment. It was hand stitched. You could machine stitch it. The only glue on it is where the little roses are glued. The little dress should have had a lining. I was so happy with the little dress that I forgot to do that. Line it or not - your choice! If you choose to line this skirt all you do is make another little slip and place it under the slip and slip stitch the 2 together. Other styles can be made using this concept. Don't be afraid to make This lovely dress is made for display - but perhaps could be worn! Reason is because you can adjust the bottom half and the top half once you put them together. These 2 dresses are different because of the type of lace they are. But they are made the same way!! The difference between this dress and the dress in the next photo that I am making - is that I am lining the other! This tutorial is long, but easy. I am just making sure that you can understand me. It is not easy writing a tutorial! Materials needed: - 2 pieces of 3.5 inches wide white lace - tiny narrow ribbon - OPTIONAL: a small amount of cheesecloth or fabric (for lining) - small roses or other items to decorate - needle and thread - glue Directions: This photo shows about the width of the white lace that I have used. You can buy this lace at your fabric store - but I have always used baby clothes when making my miniature doll clothes. That's where this lace comes from. And this is a lot of lace for $2.00 as well as the lovely white cotton!!! This is the cheesecloth that I am lining the bottom half of my skirt with. Notice that by my thumb the cheesecloth is doubled. It is thin so you will need to cut 2 pieces of this. Or use a piece of fabric for lining. Cut 2 pieces of the lace - about 5 inches long. One piece is used for the skirt - the other piece for the top. Put one piece aside for now. (now is the time that if you want the doll to wear the skirt - then you will have to adjust by adding more lace width if the doll is fat). If the doll is skinny then the measurements that I gave above should suffice. Lay one piece of lace on your table, make sure it is the backside and is straight. Lay your cheesecloth or fabric on top of this lace. Make sure everything is straight and that the cheesecloth or lining does not hang past the lace. If everything is to your liking, then pick it up gently and stitch through all the layers by hand or machine. Cut off any excess seams. Turn the lace skirt right side out. If you use cheesecloth or fabric, be sure to pull the lining up, because the top is not sewn together. For display - stitch thru all 4 layers at the top to close. This is what the top should look like, if this is for display. The skirt is finished so set it aside. For the doll to wear - Start at the top back seam and with a needle and thread, stitch through the lace and the lining. See here I am - stitching around the skirt. Make sure that when you stitch that you stitch thru the cheesecloth or the fabric lining. When finished - place it on your doll, gather tightly, knot it and cut off the thread. It doesn't matter if the knot shows because it will be hidden by the ribbon. If you see any cheesecloth lining peeking out below the skirt then cut it off. Cheesecloth stretches. If you have fabric, then lightly put on some 'Fray Check' or narrowly hem it. To Make The Top - Take the second piece of lace that you cut earlier. Place wrong sides together. Make sure the bottom edge is even. Starting at the top of the lace , make a knot and sew down to the bottom edge, knot off and cut off the thread. I like to stitch down to the edge and then back up. Stitching this way gives it strength. You are unable to see any of the stitching. Cut off excess from the seam. Now turn the lace piece right side out. Finish making for display - Now take the skirt that you finished earlier and put it under the top as I show here. Take it to your miniature doll and adjust the top up or down so that the top of the lace ruffle hits where her breast should be. Keep adjusting it until you get it like you want it. Once adjusted to your liking, put the 2 pieces together. Make sure that all the seams line up. Then hand-sew thru all the layers of the top and the skirt from the front to the back - as shown in the picture. Gather with your fingers to make it all fit together. When finished sewing - knot it. See my knot. I am not worried about it because it will be hidden by the ribbon. Ribbon at the waist - Cut a 9 inch piece of ribbon. Wrap it around the dress hiding all the stitches. Make sure you hide the knot. Tie the ribbon in a knot or a bow. Cut off excess ribbon. Sorry no photo for the ribbon - refer to the first photo. For Straps - Cut 2 pieces of matching skinny ribbon each of them about 2 inches long. On the front side, glue or hand-stitch both straps to the inside top. Glue or hand-stitch to the back one strap at a time. Play with the skirt until it looks the way you want it to. Adjust gathers if needed. I took a small piece of cheesecloth and stuffed it inside the top to give the illusion of it being lined. Display dress is finished - Hang on a hanger! For doll to wear - Use the directions for making the top. Make a knot in thread. On the inside of top, run a gathering stitch around the top. Place on doll where you want. Pull tight but do not break the thread. Knot and run the needle to the inside of the top, Pull the knot to the inside and cut off excess thread. On outside adjust gathers so they are even. Follow directions for the 'ribbon at the waist'. Make sure the ribbon hides the skirt underneath. Follow directions for the straps. If need be, you can stuff the inside top with pieces of cheesecloth. Thanks for stopping by! Hopblogger