- - For 4x4 (3.5" x3.5") Posts - - For 4x4 (3.5" x3.5") Posts- - For 4x4 (3.5" x3.5") Posts This listing is for our Outside Corners and other individually sold brackets made to fit 4 x 4 Posts and Beams. If you want them for 6 x 6 posts, click here: https://www.etsy.com/listing/708942856 (NOTE: All our brackets are based on the dimensional size of the lumber but we can make them actual 4"x4" or 6"x6" for you, if needed. Just let us know your ship-to zip code, the parts and actual size(s) you would like and we can let you know the total cost for custom brackets made to fit your saw-mill-cut posts.) Build your own rugged and heavy duty PostHugger™ Pergola, Double Pergola, shop/garage/CNC table, deck or even a wedding arch chuppah with our USA made 1/8" steel Outside Corner brackets and more! Also great for fixing/reinforcing the one you already have! These are not flimsy/bendable metal. We make them using 1/8" thick steel - a single corner bracket weighs just over 2 pounds - - strong enough to take what you throw at it (or what you throw it at!), but not so heavy where they are hard to work with. Our brackets can be installed using any 1/2" wood lag screws or in instances where there will not be a collision of bolt holes, 1/2" thru bolts. If you use lag screws, we recommend 1/2" x at least 2" length for 4x4 posts and at least 2.5" length for 6x6 posts, with longer bolts adding more strength. WOOD AND BOLTS/LAG SCREWS ARE NOT INCLUDED WITH OUR BRACKETS. Please note that unless you choose the powder coated option, these ship as raw, unpainted steel. You can either paint them the color of your choice, finish them with a clear coat, or allow to achieve a natural rust patina over time. ***Powder Coated Brackets: If ordering brackets in the black powder coat, please allow an additional 1-2 days for shipping & delivery.*** WHY BUY POSTHUGGER? • We are the original designer of these brackets, often copied by others but never equaled! • We use 1/8″ steel which is thicker than a Quarter and a Dime stacked on top of each other. • Unlike others who just cut and ship steel right off their table, we take the time to hand debur and wire brush both the inside and outside of every piece. • All powder coating is done in-house to ensure a quality application on each and every piece. • We use only 100% first-rate, high quality powders, which are all made in America. • We develop all designs ourselves and, unlike some, never poach the intellectual property of others. • We proudly stand behind all our products. • All our PostHugger™ Brackets & metal artwork products are Made in America with American-Made Steel! *************************** Our Brackets Product Line includes: Outside Corner Brackets - bent at a 90 degree angle to fit over any 4 x 4 post (3.5" x 3.5"). There are two 1/2" holes on each of the top ears for fastening to cross members and four 1/2" holes on the bottom leg for mounting to the legs. (The holes for the legs are offset so that if you want to thru bolt, you don't have to worry about hitting any of the other installed bolts!) Flat T brackets - join other parts of your design. Bent L’s - use where you want an inside corner. Flat L’s - Flat like the T, but without the third leg. Double Inside Corner - This is used on an inside corner to support two incoming posts. The holes are offset so that if used on the same post as an Outside Corner, they will not collide. Two Piece Post Base - Used to bolt a post to concrete or other suitable surface. If your post is going up against a wall or other flat surface which would interfere with having four feet, you will want to use either our Half-a-Post-Base, our 3-Sided Post Base (which has three feet) or our Full Post Base (which has just two feet) so that your post can be closer to a wall. Half a Post Base - This bracket is just one half of the Two Piece Post Base, for those who only need one (or another odd number). Three-Sided Post Base - Similar to our other Post Bases, but with three sides/feet. Full Post Base - Similar to our other Post Bases but with fours sides and just two feet (on opposite sides). Legless T™ - This bracket is the same dimensions & placement of bolt holes as the “T” - just without the bottom “leg” of the “T”! It measures 5.5" x 16.5" for a 6x6 post, and 3.5" x 10.25" for a 4x4 Post.

Flat X™ Bracket - 90 degree cross angle brackets to provide extra, heavy duty support to new or existing DIY builds & structures. Flat Knee™ - This knee brace bracket sits flush against the outside of a knee joint. Bent Knee™ - This knee brace bracket is for use where you have a post coming in to meet another post at a 45° angle and want a bracket in the knee bend itself. *****EXTRA SHIPPING COST ON ALL BRACKET ORDERS TO NON-CONTIGUOUS UNITED STATES.***** Please call 470-626-5989 to place your order. If you would like to see customer photos (and a video!) of some of our brackets in use, copy and paste the following URL into your browser: https://posthugger.com/photos/ © 2024 Thermo-Flex Technologies, Inc. - All Designs, Photos, and Text are the Intellectual Property of Shop Owner and are not to be copied without express written permission.