I'm head over heels for mechanical cards. I spend a ton of hours planning and figuring out folds, tabs and slots. This is a very simple card on the outside that will surprise you when you open it. The SVG given provides the base card, the mechanism, the outline for the stamped image (electronic die) the cheese paths and the faux stitched front panel with the sentiment. Please notice, there's a matted panel on the finished card that was cut using a My Favorite Things Diagonal Stitched Die not included in the file. I also used a die to cut the front white panel on the finished card. I just like bettr the clean cut that dies provide for big pieces. The sentiment was written with the Cricut, using a Pilot Precise V5 pen. This is a great COPIC friendly ball pen to have and fits perfectly on the pen adapter of your machine. Ungroup the pattern, select your top layer, change the function from cut to write and attach it to the underlying layer. I wanted to keep the front of the card as simple as possible to draw all the attention to the inside of the card. Don't be intimidated to try it out, there's only four pieces to this mechanism. Card base (peach cardstock) Mehanism (yellow) Rotating piece mouse) Mechanism cover (cheese) The card base is an A2, top folding card in landscape mode, with cut marks indicating the main fold and the placement of the mechanism. It is useful to mark the center folding line with a scoring board for accuracy. The mechanism has two layers, a scoring layer and the path itself. Ungroup the file, change the function of your top layer to score and attach it to the layer below. The cheese has two layers: a solid bottom layer cut from a light orange cardstock and a top holey layer. I colored the inside of the holes using a dark orange COPIC marker and added some highlights with a white gel pen in the right places. I also inked the top layer using Scattered Straw Distress Ink on a Mini Ink Blending Tool. I used Aleene's Tacky Glue to join both layers. I like using liquid glue to strengthen the cardstock. For the Character, I used Express Blending Card, in my opinion, the best cardstock for smooth COPIC marker color transitions. I used the mouse, the cheese and the sentiment from an OAK Tree Stamp Set, part of the Fall 2016 release called Marcello. I stamped the images using Memento Tuxedo Black Ink and colored them with COPIC markers. I then cut them using the Electronic Dies OAK Tree Stamps gives for free at their site. I then, made a slit above and below the mouse's hands to insert the little cheese wedge. Stamp your sentiment on the inside of the card base Next, fold the mechanism following the scoring lines. Use the following image for reference. Using a strong glue, adhere the mechanism to the card base, using the reference marks. Apply glue to the tabs and only to the tabs. Fold the lower tab and attach it to the base. Align the corners of the folded tab to the reference marks. Press firmly and let it dry a couple of seconds. Fold the mechanism down and close the card Fold mechanism down. Hold mechanism down Press firmly. You can place an acrylic block on top to let it dry. Open the card and check the for the mechanism to be working properly. Glue the mechanism cover folding the tab back and aligning it to the reference marks. Apply glue to both tabs Align with left mark. Align with right mark. Press firmly Or put an acrylic block on top Finally, glue the character to the mechanism rotating arm. Use this image as reference for correct placement Allow to dry for a couple of minutes. Open and close the card several times to train the folds and allow for proper movement. I hope you like this card. Please take time to leave a comment, subscribe and like us on Facebook. Enjoy! Supplies List Download Click here If links don´t seem to open, please right click and select "open link in a new tab", it should take you to a save file dialog. Let me know in the comments if links don´t work, thanks.
Здравствуйте, дорогие гости и жители нашго леса, Избушка вновь приветствует Вас! С вами Ёжка-Таня! Сегодня стартует второй этап нашего совместного проекта "Волшебный интерактив". Очень рада, что вам понравились новые интерактивные конструкции, столько приятных слов написали, так приятно! Ждем всех остальных участников и просматриваем ваши сказочные развороты! Совсем скоро узнаем победителя этого этапа. Победитель будет выбран из тех участников, которые сдали свой разворот в срок! Это обязательное условие и правила участия у всех одинаковые. Развороты по второму этапу принимаются до 4 февраля включительно. Обязательный элемент - использование конструкций с нашего мк. На этой неделе мы будем создавать две новые интерактивные конструкции, они и будут являться ОЭ второго этапа, всё остальное оформление страничек по вашему желанию. Ну что, предлагаю окунуться с головой в создание нового разворота))) Леший забегал на днях ко мне, навестить да посмотреть как успехи по созданию его дивной вещицы. Увидел, да удивился! Теперь ждет не дождется следующих волшебных страничек, а я тороплюсь и колдую днями и ночами над ними. Узнала я у Лешего, что внучек - то дорогой, любит на звезды смотреть и мечтает полетать по звездному небу. Пришли тогда мне в голову две чудесные конструкции интерактивные. Подробнее рассмотрим их ниже. Что у меня получилось покажу и вам! Страница №3 Наколдовала я интерактивную конструкцию под секретным названием "Телескоп". Посмотрите, правда же как настоящий))) Думаю что удивиться внучек Лешего, ведь так любит он смотреть на звездное небо. На верхней страничке помимо интерактивного элемента я разместила 4 подложки для фото 9х13 см и осталось место для фото большего размера. Начинаем колдовство))) Итак, для создания конструкции мне понадобились детали следующих размеров: 1. 4х6,5 см 2. 13х22,3 см 3. 17х31,3 см 4. 21х43,3 см Для создания первой выдвижной детали мне понадобились Деталь №1 и Деталь №2. Согласно схеме я пробиговала и сделала прорези в Детали №2. Обе детали я сразу задекорировала. Так же мне потребовалась деталь размером 1,5х6,5 см. Прорези можно делать на любом удобном вам расстоянии, я делала прорезь отступив по 1,5 см от линии бига и от края детали. Вставила полосу в прорези и загнула кончики и склеила полосу. Получился "бегунок". Нанесла клей на "бегунок", выровняла свои детали приклеила Деталь №1. Далее я загнула нижний край детали, вот, что у меня получилось. Картинка прекрасно движется. После этого я нанесла клей на на верхнюю часть детали и склеила всю конструкцию. Далее мне потребовалась Деталь №3. Согласно схеме пробиговала и сделала прорези в детали. Деталь №3 предварительно задекорировала подложкой для фото. Сделала прорези отступив 2,5 см от линии биговки и от края. Подготовила "бегунок". Вставила по аналогии с предыдущей деталью "бегунок" в прорези и склеила его края. Нанесла клей на "бегунок". Склеила свои детали. Загнула нижнюю часть конструкции и, нанеся клей на верхнюю часть детали, приклеила её. Далее я взяла Деталь №4. Согласно схеме нанесла линии биговки и сделала прорези, они немного шире, их ширина 1 мм. Сделала подходящий по размерам "бигунок", вставила в прорезь и с другой стороны склеила кончики. Приклеила всю конструкцию к последней детали. Проверяю чтобы все детали заходили друг в друга без затруднений. Затем клеила всю конструкцию. Нанесла тонкую полосу клея на деталь и загнула нижнюю часть. Важно! Это сделала только на последней детали, на предыдущих этого делать не нужно! Дальше я нанесла тонкую полосу клея на боковую и верхнюю часть своей детали и склеила всю конструкцию. Вот что у меня получилось. Весь механизм работает отлично, далее я приступила к декорированию страницы. Вся конструкция получилась размером 14,5х21 см, что соответствует остальным страницам. Предлагаю Вам посмотреть видео МК по созданию данной конструкции. ****** Страница №4 На второй страничке интерактивный элемент прячется за вот этой прекрасной композицией. В рамочку Леший поместит фото внучка своего, и "полетит" он под звёздным небом, следуя своей мечте. Вот он интерактивный элемент! Эффект парения всегда здорово смотрится в альбомах, но этот элемент при открывании еще и движется в сторону, в моем альбоме он движется в правую сторону. Ну что, приступим))) Для создания данной конструкции мне понадобились детали следующих размеров: 1. Основа 21х29 см 2. Подложка для фото 14,5х21 см 3. Для механизма 7,5х11,5 см 4. Две полосы для карманов 6,5х18,5 см Я взяла деталь размером 7,5х11,5 см и нанесла все линии биговки согласно схеме. Вот такая разметка должна получиться и у вас))). Весь процесс создания такой детали вы сможете увидеть в видео МК. После нанесения всех линий бига я срезала угол детали. Согнула по всем линиям свою деталь. Далее сформировав конструкцию я склеила её. Наносила клей на показанную область. Далее мне потребовалась деталь, которая служит подложками для фото. Я склеила механизм и подложку. Клей нанесла на показанную область. Подложку приклеила сгибом в сгиб конструкции. Получилось вот так: Для того чтобы разместить конструкцию в разворот, нужно задекорировать его скрапбумагой. Нанесла клей на показанную область и приклеила на страницу разворота, совместив сгиб конструкции и сгиб разворота. Затем нанесла клей на другую сторону механизма и приклеила ко второй странице альбома. Прижала канцелярскими зажимами и подождала до полного высыхания клея. Не торопитесь открывать странички, чем дольше дадите просохнуть клею, тем лучше будет держаться ваш механизм. Вот так выглядит конструкция на развороте. Вид сбоку. Предлагаю посмотреть видео МК по созданию данной конструкции. ******* Ну что, дорогие мои, на этом всё! Ждем ваши волшебные работы до 4 февраля! Обязательный элемент - использование конструкций с нашего мк. Всем прекрасных выходных и плодотворной недели. Спасибо за внимание и пока-пока!
It may look complicated but a DIY Boomf wild card is fairly easy to make as long as you have the right template. Watch and learn how to make
Hello crafty friends,I want to share this fun pop-up card using the Stuffed Santa stamp set and Fireplace dies. I applied the moving cosmos technic of the card in the last video to this card, and Santa made moving in this card. I had a difficult time making this Christmas gift pop-up in the fireplace feature
It may look complicated but a DIY Boomf wild card is fairly easy to make as long as you have the right template. Watch and learn how to make
We are introducing some cute new characters today with Stackable Cuties. These itty bitty cuties were illustrated with fun and functionality in mind. Stack them high or use them alone when the occasion calls for them! There's a total of, count them, 10 cuties! My favorite? The little elephant obviously! Although I hear that unicorn is quickly becoming a fan favorite! What's yours? Joining us today is a very special guest - Keiko Ichikawa! Keiko @happy_tree_studio wowed us with her creations on Instagram, pretty much all her projects are so so beautiful an intricate! You can really tell she puts her all in everything she creates! ME supplies used: Stackable Cuties (stamps and dies available 1/15/2019), Friendship Sentiments (stamps available 1/15/2019) Fun announcement, our friend Anita Chang @changanit has been making waves on our Facebook Page with her wonderfully delightful interactive creations. We teamed up with Anita and created Wiper Surprise! Now you can easily create these surprise pop up cards! Wiper Surprise comes with one large base which you'll need to die-cut two times, one for the back of the card base and one for the front of the card base. It also comes with 5 different pop up mechanisms to choose from! Each one will pop in different ways! I created this card using Stackable Cuties and the new Wiper Surprise. I keep it very basic so you can follow along with assembly easily. It's super simple to create the surprise pop! [Click HERE to watch the video on YouTube] And now here is a simplified pictorial on how to assemble the Wiper Surprise. As mentioned, the Wiper Surprise die set comes with 5 different mechanisms, they all work similarly, so you'll have to play with them and see which you like best! They will also pop up in different places, closer or further out from the fold. I try my best to illustrate this using colored cardstock. Refer to the final image to see where each one will pop up your image! Thanks for coming by today, check you back here tomorrow!