Способ вшивания молнии, который я сейчас покажу, на данный момент считаю лучшим для текстильных сумок. Конечно, ничто не вечно. И будет еще что-то любимое, наверняка. А пока... представляю Вам моего фаворита:). Все-таки, сумка из ткани и кожаная сумка - это совсем не одно и то же. Если сумка из кожи может себе позволить упрощенные технологии и от этого только выиграет, то сумка из ткани нет, если только это не обусловлено стилем или функциональным назначением. Поэтому максимум внимания деталям! Молния с планками - самая важная из них! И это совсем несложно. Даже, наоборот, очень даже просто. Начинаем с определения размеров планок и обтачек. Глубина, на которую опущена молния от уровня сумки, должна быть 2 - 3 сантиметра. Меньше смысла нет, а больше, наверно, не надо. Припуски на швы в деталях сумки я оставляю 1 см. Итак, нам потребуется: 1. Молния. Длина молнии должна быть хотя бы на 10 сантиметров длинее, чем ширина сумки, но в разумных пределах. Хотя... Ее всегда можно обрезать. 2. Верхняя обтачка. Ширина = (ширина сумки + припуск 1 см) * 2 . Высота с припусками 4 - 6 сантиметров. Укрепить флизелином. 3. Нижняя обтачка. Ширина, как у верхней. Лучше вообще их выкроить, как одну деталь. Укрепить флизелином. А потом разрезать. Так быстрее. Ширина = (ширина сумки + припуск 1 см) * 2 Высота с припусками 5 см и более. Не экономьте на глубине этой обтачки. Подкладка наружу выглядывать не должна. 4. Планки для молнии. 4 штуки. Ниже определимся с их размерами. Тут схемку лучше нарисую. Я же теперь художник. Ну чтобы не позориться своим уровнем владения графическими редакторами. Самое важное - правильно рассчитать размеры планок. А еще лучше попробуем формулу вывести. На схеме ниже: вид сумки сверху. Первым делом надо определиться с шириной застежки А. Она зависит от модели и личных пристрастий. На моей сумке - 5 см. Периметр рисунка равен: Две ширины сумки без припусков. Расстояние В Вы тоже выбираете сами. Мне нравится, чтобы оно было минимальным, например 0,5 см. Но именно на этой сумке поняла, что это расстояние зависит и от толщины сумки. (Вы же помните про слимтекс в 2 слоя:)). Так вот. На толстых сумках изгиб получается неэластичным и ему надо больше места, чтобы красиво выгнуться. Поэтому 0,5 см применяем не всегда. Пробуем 1 см или даже 1,5 см. Теперь рассчитаем длину планки С. С = Ширина сумки - А - 2В Формулу я, конечно, упростила. Синусы и косинусы решила не применять (да и подзабыла уже). Но Вы же помните теорему Пифагора. И то, что половина свободной дуги сумки ну никак не будет равна 1/2А + В. Я тоже помню. Но заморачиваться не буду. И Вам не советую. Таким образом сделаем дополнительную посадку для эластичности. Много раз так шила. Формула работает. Это как в самолетах. Мне муж рассказывал. Он когда-то проектировал ракеты. Так там тоже: сначала долго-долго считают, потом по расчетам делают профили, а потом все равно их продувают в аэродинамических трубах. Проверяют расчеты на практике. Сумка, конечно, не ракета. Но на практике проверено:) Ширина планки Н без припусков будет равна 1/2А - 1/2 ширины молнии. Обратите внимание, что молнию можно вшить по-разному. Можно оставить много тесьмы молнии контрастного цвета, например. Тогда планки будут уже. А можно под самые зубчики. It depends, короче. Но лучше планки сделать пошире, а потом уже с вшитой молнией подравнять. Я скажу когда, да Вы и сами поймете. Итак, планка с припусками - прямоугольник со сторонами: С с припусками = Ширина сумки - А - 2В + 2 см на припуски Н с припусками = 1/2А - 1/2 ширины молнии + 2 см на припуски И таких 4 штуки. Лучше выкроить одной деталью, укрепить флизелином, а потом разрезать на четыре штуки. Тут я флизелином не укрепляла. Потому что бортовка мешковина и так лучший флизелин. А в остальных случаях надо обязательно! Вообще-то это самый сложный и неприятный момент в этом процессе - выкроить эти планки. Но и самый ответственный. Результат зависит именно от этого, а не от танцев с бубном со швейной машинкой. Поэтому относимся с полной ответственностью к раскрою! После раскроя на каждой из четырех планок заутюживаем припуски 1 см на боковых срезах, как на фото внизу. И обшиваем молнию планками. Молнию я уже обрезала и край обшила кусочком кожи. Тканью здорово обшивать тоже. Но что-то сделать с краем молнии настоятельно рекомендую, потому что он остается свободным и необработанный край как-то не comme il faut. Для этого, сначала одну планку фиксируем булавками к тесьме молнии, при этом, прячем хвостик молнии как на фото, чтобы он впоследствии не выглядывал. С другой стороны прикладываем вторую половину планки, совмещая боковые срезы, и фиксируем булавками уже 3 слоя. Сшиваем детали на швейной машине. Я использую лапку для молнии.. Аналогично обрабатываем другую сторону молнии. Затем выполняем с изнаночной стороны шов, фиксирующий припуски. На фото ниже он обозначен розовой линией. Шов прокладывается именно в таком положении, как на фото, через нижнюю планку, тесьму молнии и все припуски. Верхняя планка не прошивается на этом этапе. Этот шов выполняется без предварительной заутюжки. Он очень удобно выкладывается руками. А вот после выполнения этого технического шва заутюживаем лицевую планку на место. Все получается идеально, только боковые срезы у нас пока свободные и незастроченные. Вот теперь по лицевой стороне (если есть наше всё - моя любимая лапка G, то используем её) отстрачиваем планки с трех сторон (на фото следуем за белым кроликом розовой линией). Теперь планки с молнией еще раз утюжим и обрезаем до размера А плюс 2 см на припуски. Отмечаем середины планок, сгибая деталь и срезая ножницами небольшие уголочки. Это самый быстрый, точный и наглядный способ нанесения отметок на срезы. И самый экономный, наверно... Ножницы точно у всех есть). Точно также отмечаем серединки на обтачках сумки (со всех сторон, в т.ч. и со стороны подкладки, потом будете радоваться). Если обтачка цельная, то таким же образом отмечаем и место бокового шва, которого нет. Только не забываем, что если обтачка без бокового шва, то складываем не ровно пополам, а пополам только до места шва, как на фото внизу (розовые линии: левая линия - срезы, правая линия - сгиб). После нанесения отметок соединяем планки молнии с обтачками. Начинаем всегда с соединения центров, а потом расползаемся к бокам. Тут еще и следим, чтобы края планок были симметричны. Размещаем планки между обтачками сумки и прошиваем швом 1 см от края (если рассчитывали припуски 1см). Выполняем любимый мною технический шов - фиксируем припуски на нижнюю обтачку (лапка G нам в помощь). Я тут еще кружевце пришпандёрила, чтобы шов соединения с подкладкой был ваще красивый. (Правда потом сие кружевце начало наглым образом распускаться, и я все фестончики посрезала, поэтому в готовой сумке кружевца нет, а какое-то недоразумение торчит:)). Сшиваем обтачку в кольцо швом 1 см от края. Теперь пришивваем обтачку к сумке, не обращая внимания на молнию. Как пришивать обтачку я подробно показывала в МК по пошиву сумки - Птицы. Моя корзинка оказалась слишком толстой для отстрочки края сумки. Но и без неё неплохо держит форму. Еще необходимо обтачку прикрепить к сумке, а то застежка будет незафиксирована. Я не люблю сквозных швов отстрочки. По-моему, чем их меньше, тем аккуратнее смотрится изделие. Поэтому я подшиваю обтачку руками к сумке вручную после пришивания подкладки через отверстие в ней. Я, к сожалению, не сфотографировала этот процесс (увлеклась чего-то...) В МК по сумке-птице я показывала такое закрепление отдельных деталей после пришивания подкладки (а в нашем случае надо пройтись по всему периметру) . И вот такой у нас получается хвостик. В некоторых моделях сумке очень идет, когда он выглядывает наружу. А не хотите - можно спрятать. Точно так же вшивается молния в сумку с криволинейным срезом. Вот например в сумке Акварель. Имеем изогнутый срез верха и много фото застежки. Поэтому сейчас именно на ее примере схемку нарисую. Все просто. Рисуем профиль сумки. Параллельно линии верха, ниже её на 2-3 см чертим желаемую линию расположения застежки сумки ( у меня это красная линия). Ниже нижней точки красной линии сантиметра на 3 чертим горизонтальную линию. Это линия притачивания подкладки. У нас уже получились выкройки нижней и верхней обтачки. Только без припусков! Не забудьте их добавить! И еще. При криволинейной линии верха нижние и верхние обтачки верха необходимо выкраивать из двух деталей. Замеряем длину красной линии и принимаем ее за "Ширину сумки" для расчетов размеров планок. И далее по алгоритму. Единственное, что перед пришиванием обтачек к планкам необходимо верхнюю и нижнюю обтачки сшить по одному боковому шву. Вот и все. Главное таки - правильно выкроить планки! Не забудьте! Удачи! .
Модная одежда и дизайн интерьера своими руками
Модные сумки шопперы, стильные, и ни у кого второй не будет. Спасибо за фото. | Вступай в группу Девочки и Куколки Рукоделие пэчворк в Одноклассниках
The inspiration for this little pouch came from a another zippered pouch I saw on Pinterest: wavey pleated clutch yorktownroad etsy store I was also inspired by this quilt block: textured quilt block TeresaDownUnder WP blog And so I fooled around with some fabric and this little guy is what I come up with: I began with a long strip of this burgundy fabric. I don't know what it's called, but it's rather thick, slick, shiny, and frays like mad. Another cool aspect is that the fabric has a holographic effect--it looks black if you tilt it to the right angle. I'm sure it would be perfect for formal dresses or maybe a dressy fitted top. Of course I wasn't planning on making either when I picked it up out of the Red Tag bin at JoAnn's. I made two pleat-cheats which consisted of cardboard strips measuring 1.25" and 0.75". Why make 2 different sizes? Well, tried to make then all the same size, but then I ended up with something that wouldn't lay flat. One side of the pleat needs to be longer than the other side if you want them to lay flat like this: Here's a handy-dandy diagram to show you what I mean: I stitched down one side and flipped the pleats on the other side to lay the opposite direction so I could stitch that side as well: I added some fabric to each side and it ended up looking a lot like the quilt block I showed earlier: I trimmed my version of the quilt block and fiddled around with it until I found something I liked. I was really pleased with how the pleats looked when I folded the block in half. So I set out to make a little zippered pouch. Now, most of the time when you make zippered pouches, you're dealing with a front and back. This pouch I made is slightly different because the outside is all one piece. Of course, I didn't take pics of the whole process (slapping forehead) but there are oodles of tutorials on zippered pouches. Why make another one? I will say, the pouch being tiny like it is sure made top-stitching around the zipper a major pain in the arse. I won't be trying this again in these proportions any time soon (never!). I did finish it though, and I love how it turned out. I made this pouch for the Fab Folds Sewing Challenge. I host a sewing challenge every other month and September's challenge was to make something using pleats, pin-tucks, or smocking. It's a fun way to meet new bloggers, learn new sewing techniques, and get totally inspired! I have a challenge page you can go to on my menu bar and visit previous challenges and see what's current now. I'm curious. What do you know about pleating, pin-tucking, and smocking? What have you been sewing lately? What do you think about my Petite Pleated Pouch? Have you ever been in an online sewing challenge? Happy crafting and big hugs from Montana,
Джинсовые переделки. Made of Jeans Denim ~
Посты по теме «Шитьё», добавленные пользователем Ирина Михайловна Старостина на Постилу
Сегодня хочу предложить вашему вниманию удивительные сумки ручной работы от разных мастеров. Просто для восхищения!
Грамотно выбранные женские прически на короткие волосы визуально убавляют возраст. Выбрать красивые стрижки дамам после 40 лет в 2020-2021 году помогают
Из старых джинсов можно сделать рюкзак своими руками. Какими выкройками и мастер-классами лучше воспользоваться? Как украсить полученный рюкзак?
Made of Old Jeans Denim
O que é o Patchwork Crazy? Como Fazer? - Veja Montar e Costurar o Artesanato em Crazy, Moldes e Riscos, Passo a Passos (Almofada, Colcha e Porta Tablet).
У вас завалялись старые джинсы, жилетка из этого материала или что-то еще? Тогда вам непременно надо посмотреть подборку о том, как переделка джинсов может сделать вашу жизнь ярче. Сумки, фартуки, даже обивка для кресла — всё это можно сотворить из когда-то любимых джинсов, чтобы подарить им новую жизнь. Представляете, на что способна джинсы?) Еще больше идей вас ждет в видео-подборке. Джинсы — это очень полезная вещь. Сейчас практически ни одна модница не представляет свою жизнь без них.