Ready to harness the power of the sun with RV solar panels? Use our complete beginner's guide to RV solar panels to learn what you need.
We share our first year experience with 2625W of solar panels, which were working perfectly, until we discovered: you can lose a solar panel.
Can Solar Panels Actually Power the RV Air Conditioner? The answer may surprise you and you might understand our non-techy answer too!
Beat the heat! How I built solar screens on my RV windows. We've been in cooler regions of the United States this summer, so heat wasn't a problem -- but we had to come back to central Texas this month! Heat over 100 degrees! I made really nice adjustable, removable fabric awnings for my previous camper. (If you want to know how, click here) I liked them a lot, and they are super cute, but they have a couple drawbacks. If it gets really windy in the middle of the night, they will bang on the camper. Sometimes loudly enough that you have to get out of your cozy bed and put them away. It took a lot of time to make the awnings - making the solar shades take almost no time at all! So, I came up with the idea of solar screen covers for the windows. There are a lot of advantages. There is a video at the end of this article that shows how stable they are in a windstorm. They block up to 90% of the sun's heat. Unlike the silver stuff, you can see through your windows and don't feel like you're living in a cave. They are easy to put up and take down. You don't have to remove them if it rains or is windy. You can open and close all your windows, including the emergency window without removing them. You can have airflow through the trailer and still block the heat Best of all YOU CAN SEE OUTSIDE! The screens are held up with magnets and are easy to install and remove without a ladder. Interested? Read on to see how I did it! Note: all my affiliate links will generate money for your favorite charity! They are all set to go to smile.amazon.com To hold up the screens, I glued one magnet to the RV and sewed a matching magnet into the screen. There has been discussion about using snaps, but I didn't want to make holes in my camper. I can remove the magnets if I ever want to. This is what I used: Solar Screen (obviously) Magnets Normal Sewing Machine (I use a cheap Brother machine similar to this one that is AMAZING!) Heavy UV Resistant Thread These are the same size as the magnets I used. Plan on using a magnet about every 1-2 feet. My windows are small. The largest two are only about 48"'w x 24"h. If I had larger windows, I would have used larger magnets or more magnets closer together. On the 48-in windows I used 4 magnets across the top. On 36" windows I used 3 magnets across the top. On 24" windows I just put a magnet on each corner. Mostly your concerned about the weight of the screen fabric. If I had larger windows, these magnets would have worked better. Be VERY CAREFUL with the magnets, be VERY careful with them, they are extremely brittle. They will also give you a blood blister if they catch your finger between them. Once they are mounted on the RV wall, or sewn into a pocket they are pretty sturdy. It's just slamming together with no cushion that causes them to break. I cleaned the area around the windows with rubbing alcohol and stuck the magnets to the camper wall using the adhesive that was included with them. I measured the windows I wanted to cover, including the frame. Then I planned out how I was going to do it and how much screen I needed to buy. Yes, I admit I'm a bit detail-oriented about drawing out my plans and knowing exactly what I'm going to do before I start. This is the solar screen I used. I got mine at Lowe's for about $15 per roll. It took about 2 1/2 rolls. It blocks 90% of the radiant heat. It seems to work even if it's not in direct sun. If I bought the screen that blocks only 75% I could have cut my price in half. Amazon has some here. Cut pieces of solar screen about 1"-2" wider than the windows and 6-7" taller. It needs to have enough to fold over 2-3" and be long enough to cover from the magnets at the top to the bottom of the window, even longer if I was going to put magnets along the bottom of the window instead of just at each lower corner. Plain ol' school chalk marks the screens, it works great! Fold over and pin the top. I allowed 2" for the top hem/pockets. Fold and pin the 2" top hem/pockets. I sewed very close to the top edge to form a crease. I used a long straight stitch. I marked the approximate locations of the magnets and sewed a pocket about 3-5" wide for each magnet. Around each magnet pocket, I used a zig-zag stitch. Make sure to insert the magnets before sewing the final side :) This is similar to the sewing machine I have, which I bought at Sam's Club for $135 I DID NOT SEW THE WHOLE TOP FLAT - I left it open between the pockets. This is the trick to making them easy to install! I did not sew the bottom corner magnets until I test fit it to the window to mark exactly where they needed to be. I mounted the screen to the top magnets, pulled to make it even, used chalk to mark where the bottom edge of the window is, and where the magnets are. Remove the screen. Cut the screen about 1/2" - 1" below where I marked the bottom of the window. If I was putting magnets under the window, the screen would have needed to be longer. I can use my awning hook or WDH bar to push the screen up to attach to the magnets. This is why I made the magnet pockets large - so that I don't have to line it up perfectly when I am trying to install the screens. Also, if I mistakenly put one of my magnets on with the wrong polarity, I can turn the magnet inside the screen over without having to remove it from the pocket. Then I cut out the bottom magnet pockets. I only put one on each lower corner. We've had pretty good windstorms and rain and the covers haven't budged on our camper. Lastly I sewed the bottom pockets on - remembering to insert the magnet. I insert my awning pole or similar into the pocket and use it to lift my screens into place. The magnets snap together instantly all the way around the window. Then I pull it a bit to adjust it evenly. TA-DAH! Enjoy my view without the heat!! UPDATE: We had a strong windstorm and the screens stayed on perfectly! If you enjoy this blog or learn something from the article, please buy through my link and help me continue to bring you DIY ideas and tutorials. For those wondering how you would remove glued on magnets - Use fishing line to separate them from the fiberglass, Goo Gone to remove adhesive. Now Go Play Outside!
This step-by-step guide will show you exactly how to hook up solar panels to RV batteries and charge them anywhere your next adventure takes you!
Beat the heat! How I built solar screens on my RV windows. We've been in cooler regions of the United States this summer, so heat wasn't a problem -- but we had to come back to central Texas this month! Heat over 100 degrees! I made really nice adjustable, removable fabric awnings for my previous camper. (If you want to know how, click here) I liked them a lot, and they are super cute, but they have a couple drawbacks. If it gets really windy in the middle of the night, they will bang on the camper. Sometimes loudly enough that you have to get out of your cozy bed and put them away. It took a lot of time to make the awnings - making the solar shades take almost no time at all! So, I came up with the idea of solar screen covers for the windows. There are a lot of advantages. There is a video at the end of this article that shows how stable they are in a windstorm. They block up to 90% of the sun's heat. Unlike the silver stuff, you can see through your windows and don't feel like you're living in a cave. They are easy to put up and take down. You don't have to remove them if it rains or is windy. You can open and close all your windows, including the emergency window without removing them. You can have airflow through the trailer and still block the heat Best of all YOU CAN SEE OUTSIDE! The screens are held up with magnets and are easy to install and remove without a ladder. Interested? Read on to see how I did it! Note: all my affiliate links will generate money for your favorite charity! They are all set to go to smile.amazon.com To hold up the screens, I glued one magnet to the RV and sewed a matching magnet into the screen. There has been discussion about using snaps, but I didn't want to make holes in my camper. I can remove the magnets if I ever want to. This is what I used: Solar Screen (obviously) Magnets Normal Sewing Machine (I use a cheap Brother machine similar to this one that is AMAZING!) Heavy UV Resistant Thread These are the same size as the magnets I used. Plan on using a magnet about every 1-2 feet. My windows are small. The largest two are only about 48"'w x 24"h. If I had larger windows, I would have used larger magnets or more magnets closer together. On the 48-in windows I used 4 magnets across the top. On 36" windows I used 3 magnets across the top. On 24" windows I just put a magnet on each corner. Mostly your concerned about the weight of the screen fabric. If I had larger windows, these magnets would have worked better. Be VERY CAREFUL with the magnets, be VERY careful with them, they are extremely brittle. They will also give you a blood blister if they catch your finger between them. Once they are mounted on the RV wall, or sewn into a pocket they are pretty sturdy. It's just slamming together with no cushion that causes them to break. I cleaned the area around the windows with rubbing alcohol and stuck the magnets to the camper wall using the adhesive that was included with them. I measured the windows I wanted to cover, including the frame. Then I planned out how I was going to do it and how much screen I needed to buy. Yes, I admit I'm a bit detail-oriented about drawing out my plans and knowing exactly what I'm going to do before I start. This is the solar screen I used. I got mine at Lowe's for about $15 per roll. It took about 2 1/2 rolls. It blocks 90% of the radiant heat. It seems to work even if it's not in direct sun. If I bought the screen that blocks only 75% I could have cut my price in half. Amazon has some here. Cut pieces of solar screen about 1"-2" wider than the windows and 6-7" taller. It needs to have enough to fold over 2-3" and be long enough to cover from the magnets at the top to the bottom of the window, even longer if I was going to put magnets along the bottom of the window instead of just at each lower corner. Plain ol' school chalk marks the screens, it works great! Fold over and pin the top. I allowed 2" for the top hem/pockets. Fold and pin the 2" top hem/pockets. I sewed very close to the top edge to form a crease. I used a long straight stitch. I marked the approximate locations of the magnets and sewed a pocket about 3-5" wide for each magnet. Around each magnet pocket, I used a zig-zag stitch. Make sure to insert the magnets before sewing the final side :) This is similar to the sewing machine I have, which I bought at Sam's Club for $135 I DID NOT SEW THE WHOLE TOP FLAT - I left it open between the pockets. This is the trick to making them easy to install! I did not sew the bottom corner magnets until I test fit it to the window to mark exactly where they needed to be. I mounted the screen to the top magnets, pulled to make it even, used chalk to mark where the bottom edge of the window is, and where the magnets are. Remove the screen. Cut the screen about 1/2" - 1" below where I marked the bottom of the window. If I was putting magnets under the window, the screen would have needed to be longer. I can use my awning hook or WDH bar to push the screen up to attach to the magnets. This is why I made the magnet pockets large - so that I don't have to line it up perfectly when I am trying to install the screens. Also, if I mistakenly put one of my magnets on with the wrong polarity, I can turn the magnet inside the screen over without having to remove it from the pocket. Then I cut out the bottom magnet pockets. I only put one on each lower corner. We've had pretty good windstorms and rain and the covers haven't budged on our camper. Lastly I sewed the bottom pockets on - remembering to insert the magnet. I insert my awning pole or similar into the pocket and use it to lift my screens into place. The magnets snap together instantly all the way around the window. Then I pull it a bit to adjust it evenly. TA-DAH! Enjoy my view without the heat!! UPDATE: We had a strong windstorm and the screens stayed on perfectly! If you enjoy this blog or learn something from the article, please buy through my link and help me continue to bring you DIY ideas and tutorials. For those wondering how you would remove glued on magnets - Use fishing line to separate them from the fiberglass, Goo Gone to remove adhesive. Now Go Play Outside!
Item specificsCondition
[Portable & Powerful] - With a 300W AC inverter, 204Wh capacity, 6 outlets, yet weighs only 7.9 lbs, this power station is your perfect partner for outdoor adventure, camping, RV trip or even home backup. [Fast Charging] - With 270W Turbo Charging, charging AC2A from 0-80% takes only 40 mins, and 100% in 70 mins. You can also get it charged via solar panel, car, and lead-acid battery. [Safe & Durable] - Built with LiFePO₄ battery batteries and BMS for safety and longevity. The AC2A can be activated even when the battery runs out, making it a perfect power source for emergency relief. [App Remote Control] - Using the BLUETTI App, you can monitor its status, set the charging / discharging mode, and achieve an OTA update on your phone. Intelligent power management made easy. [What You Get] - BLUETTI AC2A portable power station, AC charging cable, solar charging cable, user manual. Brief content visible, double tap to read full content. Full content visible, double tap to read brief content. Details Brand BLUETTI Wattage 300 watts Fuel Type Electric Power Source Solar/AC/Car Recommended Uses For Product Camping See all product information
Expand your solar power setup with an additional 195-watt solar panel. Includes brackets and hardware for installation on your RV roof. Butyl tape comes preapplied to the mounting brackets. Uses MC4 connections (included). 1-800-940-8924 to order etrailer accessories and parts part number e72PR or order online at etrailer.com. Free expert support on all etrailer products. Great prices and Fastest Shipping for etrailer Solar Expansion Kit - 195 Watt Rigid Solar Panel. Accessories and Parts reviews from real customers.
Beat the heat! How I built solar screens on my RV windows. We've been in cooler regions of the United States this summer, so heat wasn't a problem -- but we had to come back to central Texas this month! Heat over 100 degrees! I made really nice adjustable, removable fabric awnings for my previous camper. (If you want to know how, click here) I liked them a lot, and they are super cute, but they have a couple drawbacks. If it gets really windy in the middle of the night, they will bang on the camper. Sometimes loudly enough that you have to get out of your cozy bed and put them away. It took a lot of time to make the awnings - making the solar shades take almost no time at all! So, I came up with the idea of solar screen covers for the windows. There are a lot of advantages. There is a video at the end of this article that shows how stable they are in a windstorm. They block up to 90% of the sun's heat. Unlike the silver stuff, you can see through your windows and don't feel like you're living in a cave. They are easy to put up and take down. You don't have to remove them if it rains or is windy. You can open and close all your windows, including the emergency window without removing them. You can have airflow through the trailer and still block the heat Best of all YOU CAN SEE OUTSIDE! The screens are held up with magnets and are easy to install and remove without a ladder. Interested? Read on to see how I did it! Note: all my affiliate links will generate money for your favorite charity! They are all set to go to smile.amazon.com To hold up the screens, I glued one magnet to the RV and sewed a matching magnet into the screen. There has been discussion about using snaps, but I didn't want to make holes in my camper. I can remove the magnets if I ever want to. This is what I used: Solar Screen (obviously) Magnets Normal Sewing Machine (I use a cheap Brother machine similar to this one that is AMAZING!) Heavy UV Resistant Thread These are the same size as the magnets I used. Plan on using a magnet about every 1-2 feet. My windows are small. The largest two are only about 48"'w x 24"h. If I had larger windows, I would have used larger magnets or more magnets closer together. On the 48-in windows I used 4 magnets across the top. On 36" windows I used 3 magnets across the top. On 24" windows I just put a magnet on each corner. Mostly your concerned about the weight of the screen fabric. If I had larger windows, these magnets would have worked better. Be VERY CAREFUL with the magnets, be VERY careful with them, they are extremely brittle. They will also give you a blood blister if they catch your finger between them. Once they are mounted on the RV wall, or sewn into a pocket they are pretty sturdy. It's just slamming together with no cushion that causes them to break. I cleaned the area around the windows with rubbing alcohol and stuck the magnets to the camper wall using the adhesive that was included with them. I measured the windows I wanted to cover, including the frame. Then I planned out how I was going to do it and how much screen I needed to buy. Yes, I admit I'm a bit detail-oriented about drawing out my plans and knowing exactly what I'm going to do before I start. This is the solar screen I used. I got mine at Lowe's for about $15 per roll. It took about 2 1/2 rolls. It blocks 90% of the radiant heat. It seems to work even if it's not in direct sun. If I bought the screen that blocks only 75% I could have cut my price in half. Amazon has some here. Cut pieces of solar screen about 1"-2" wider than the windows and 6-7" taller. It needs to have enough to fold over 2-3" and be long enough to cover from the magnets at the top to the bottom of the window, even longer if I was going to put magnets along the bottom of the window instead of just at each lower corner. Plain ol' school chalk marks the screens, it works great! Fold over and pin the top. I allowed 2" for the top hem/pockets. Fold and pin the 2" top hem/pockets. I sewed very close to the top edge to form a crease. I used a long straight stitch. I marked the approximate locations of the magnets and sewed a pocket about 3-5" wide for each magnet. Around each magnet pocket, I used a zig-zag stitch. Make sure to insert the magnets before sewing the final side :) This is similar to the sewing machine I have, which I bought at Sam's Club for $135 I DID NOT SEW THE WHOLE TOP FLAT - I left it open between the pockets. This is the trick to making them easy to install! I did not sew the bottom corner magnets until I test fit it to the window to mark exactly where they needed to be. I mounted the screen to the top magnets, pulled to make it even, used chalk to mark where the bottom edge of the window is, and where the magnets are. Remove the screen. Cut the screen about 1/2" - 1" below where I marked the bottom of the window. If I was putting magnets under the window, the screen would have needed to be longer. I can use my awning hook or WDH bar to push the screen up to attach to the magnets. This is why I made the magnet pockets large - so that I don't have to line it up perfectly when I am trying to install the screens. Also, if I mistakenly put one of my magnets on with the wrong polarity, I can turn the magnet inside the screen over without having to remove it from the pocket. Then I cut out the bottom magnet pockets. I only put one on each lower corner. We've had pretty good windstorms and rain and the covers haven't budged on our camper. Lastly I sewed the bottom pockets on - remembering to insert the magnet. I insert my awning pole or similar into the pocket and use it to lift my screens into place. The magnets snap together instantly all the way around the window. Then I pull it a bit to adjust it evenly. TA-DAH! Enjoy my view without the heat!! UPDATE: We had a strong windstorm and the screens stayed on perfectly! If you enjoy this blog or learn something from the article, please buy through my link and help me continue to bring you DIY ideas and tutorials. For those wondering how you would remove glued on magnets - Use fishing line to separate them from the fiberglass, Goo Gone to remove adhesive. Now Go Play Outside!
Beat the heat! How I built solar screens on my RV windows. We've been in cooler regions of the United States this summer, so heat wasn't a problem -- but we had to come back to central Texas this month! Heat over 100 degrees! I made really nice adjustable, removable fabric awnings for my previous camper. (If you want to know how, click here) I liked them a lot, and they are super cute, but they have a couple drawbacks. If it gets really windy in the middle of the night, they will bang on the camper. Sometimes loudly enough that you have to get out of your cozy bed and put them away. It took a lot of time to make the awnings - making the solar shades take almost no time at all! So, I came up with the idea of solar screen covers for the windows. There are a lot of advantages. There is a video at the end of this article that shows how stable they are in a windstorm. They block up to 90% of the sun's heat. Unlike the silver stuff, you can see through your windows and don't feel like you're living in a cave. They are easy to put up and take down. You don't have to remove them if it rains or is windy. You can open and close all your windows, including the emergency window without removing them. You can have airflow through the trailer and still block the heat Best of all YOU CAN SEE OUTSIDE! The screens are held up with magnets and are easy to install and remove without a ladder. Interested? Read on to see how I did it! Note: all my affiliate links will generate money for your favorite charity! They are all set to go to smile.amazon.com To hold up the screens, I glued one magnet to the RV and sewed a matching magnet into the screen. There has been discussion about using snaps, but I didn't want to make holes in my camper. I can remove the magnets if I ever want to. This is what I used: Solar Screen (obviously) Magnets Normal Sewing Machine (I use a cheap Brother machine similar to this one that is AMAZING!) Heavy UV Resistant Thread These are the same size as the magnets I used. Plan on using a magnet about every 1-2 feet. My windows are small. The largest two are only about 48"'w x 24"h. If I had larger windows, I would have used larger magnets or more magnets closer together. On the 48-in windows I used 4 magnets across the top. On 36" windows I used 3 magnets across the top. On 24" windows I just put a magnet on each corner. Mostly your concerned about the weight of the screen fabric. If I had larger windows, these magnets would have worked better. Be VERY CAREFUL with the magnets, be VERY careful with them, they are extremely brittle. They will also give you a blood blister if they catch your finger between them. Once they are mounted on the RV wall, or sewn into a pocket they are pretty sturdy. It's just slamming together with no cushion that causes them to break. I cleaned the area around the windows with rubbing alcohol and stuck the magnets to the camper wall using the adhesive that was included with them. I measured the windows I wanted to cover, including the frame. Then I planned out how I was going to do it and how much screen I needed to buy. Yes, I admit I'm a bit detail-oriented about drawing out my plans and knowing exactly what I'm going to do before I start. This is the solar screen I used. I got mine at Lowe's for about $15 per roll. It took about 2 1/2 rolls. It blocks 90% of the radiant heat. It seems to work even if it's not in direct sun. If I bought the screen that blocks only 75% I could have cut my price in half. Amazon has some here. Cut pieces of solar screen about 1"-2" wider than the windows and 6-7" taller. It needs to have enough to fold over 2-3" and be long enough to cover from the magnets at the top to the bottom of the window, even longer if I was going to put magnets along the bottom of the window instead of just at each lower corner. Plain ol' school chalk marks the screens, it works great! Fold over and pin the top. I allowed 2" for the top hem/pockets. Fold and pin the 2" top hem/pockets. I sewed very close to the top edge to form a crease. I used a long straight stitch. I marked the approximate locations of the magnets and sewed a pocket about 3-5" wide for each magnet. Around each magnet pocket, I used a zig-zag stitch. Make sure to insert the magnets before sewing the final side :) This is similar to the sewing machine I have, which I bought at Sam's Club for $135 I DID NOT SEW THE WHOLE TOP FLAT - I left it open between the pockets. This is the trick to making them easy to install! I did not sew the bottom corner magnets until I test fit it to the window to mark exactly where they needed to be. I mounted the screen to the top magnets, pulled to make it even, used chalk to mark where the bottom edge of the window is, and where the magnets are. Remove the screen. Cut the screen about 1/2" - 1" below where I marked the bottom of the window. If I was putting magnets under the window, the screen would have needed to be longer. I can use my awning hook or WDH bar to push the screen up to attach to the magnets. This is why I made the magnet pockets large - so that I don't have to line it up perfectly when I am trying to install the screens. Also, if I mistakenly put one of my magnets on with the wrong polarity, I can turn the magnet inside the screen over without having to remove it from the pocket. Then I cut out the bottom magnet pockets. I only put one on each lower corner. We've had pretty good windstorms and rain and the covers haven't budged on our camper. Lastly I sewed the bottom pockets on - remembering to insert the magnet. I insert my awning pole or similar into the pocket and use it to lift my screens into place. The magnets snap together instantly all the way around the window. Then I pull it a bit to adjust it evenly. TA-DAH! Enjoy my view without the heat!! UPDATE: We had a strong windstorm and the screens stayed on perfectly! If you enjoy this blog or learn something from the article, please buy through my link and help me continue to bring you DIY ideas and tutorials. For those wondering how you would remove glued on magnets - Use fishing line to separate them from the fiberglass, Goo Gone to remove adhesive. Now Go Play Outside!
Beat the heat! How I built solar screens on my RV windows. We've been in cooler regions of the United States this summer, so heat wasn't a problem -- but we had to come back to central Texas this month! Heat over 100 degrees! I made really nice adjustable, removable fabric awnings for my previous camper. (If you want to know how, click here) I liked them a lot, and they are super cute, but they have a couple drawbacks. If it gets really windy in the middle of the night, they will bang on the camper. Sometimes loudly enough that you have to get out of your cozy bed and put them away. It took a lot of time to make the awnings - making the solar shades take almost no time at all! So, I came up with the idea of solar screen covers for the windows. There are a lot of advantages. There is a video at the end of this article that shows how stable they are in a windstorm. They block up to 90% of the sun's heat. Unlike the silver stuff, you can see through your windows and don't feel like you're living in a cave. They are easy to put up and take down. You don't have to remove them if it rains or is windy. You can open and close all your windows, including the emergency window without removing them. You can have airflow through the trailer and still block the heat Best of all YOU CAN SEE OUTSIDE! The screens are held up with magnets and are easy to install and remove without a ladder. Interested? Read on to see how I did it! Note: all my affiliate links will generate money for your favorite charity! They are all set to go to smile.amazon.com To hold up the screens, I glued one magnet to the RV and sewed a matching magnet into the screen. There has been discussion about using snaps, but I didn't want to make holes in my camper. I can remove the magnets if I ever want to. This is what I used: Solar Screen (obviously) Magnets Normal Sewing Machine (I use a cheap Brother machine similar to this one that is AMAZING!) Heavy UV Resistant Thread These are the same size as the magnets I used. Plan on using a magnet about every 1-2 feet. My windows are small. The largest two are only about 48"'w x 24"h. If I had larger windows, I would have used larger magnets or more magnets closer together. On the 48-in windows I used 4 magnets across the top. On 36" windows I used 3 magnets across the top. On 24" windows I just put a magnet on each corner. Mostly your concerned about the weight of the screen fabric. If I had larger windows, these magnets would have worked better. Be VERY CAREFUL with the magnets, be VERY careful with them, they are extremely brittle. They will also give you a blood blister if they catch your finger between them. Once they are mounted on the RV wall, or sewn into a pocket they are pretty sturdy. It's just slamming together with no cushion that causes them to break. I cleaned the area around the windows with rubbing alcohol and stuck the magnets to the camper wall using the adhesive that was included with them. I measured the windows I wanted to cover, including the frame. Then I planned out how I was going to do it and how much screen I needed to buy. Yes, I admit I'm a bit detail-oriented about drawing out my plans and knowing exactly what I'm going to do before I start. This is the solar screen I used. I got mine at Lowe's for about $15 per roll. It took about 2 1/2 rolls. It blocks 90% of the radiant heat. It seems to work even if it's not in direct sun. If I bought the screen that blocks only 75% I could have cut my price in half. Amazon has some here. Cut pieces of solar screen about 1"-2" wider than the windows and 6-7" taller. It needs to have enough to fold over 2-3" and be long enough to cover from the magnets at the top to the bottom of the window, even longer if I was going to put magnets along the bottom of the window instead of just at each lower corner. Plain ol' school chalk marks the screens, it works great! Fold over and pin the top. I allowed 2" for the top hem/pockets. Fold and pin the 2" top hem/pockets. I sewed very close to the top edge to form a crease. I used a long straight stitch. I marked the approximate locations of the magnets and sewed a pocket about 3-5" wide for each magnet. Around each magnet pocket, I used a zig-zag stitch. Make sure to insert the magnets before sewing the final side :) This is similar to the sewing machine I have, which I bought at Sam's Club for $135 I DID NOT SEW THE WHOLE TOP FLAT - I left it open between the pockets. This is the trick to making them easy to install! I did not sew the bottom corner magnets until I test fit it to the window to mark exactly where they needed to be. I mounted the screen to the top magnets, pulled to make it even, used chalk to mark where the bottom edge of the window is, and where the magnets are. Remove the screen. Cut the screen about 1/2" - 1" below where I marked the bottom of the window. If I was putting magnets under the window, the screen would have needed to be longer. I can use my awning hook or WDH bar to push the screen up to attach to the magnets. This is why I made the magnet pockets large - so that I don't have to line it up perfectly when I am trying to install the screens. Also, if I mistakenly put one of my magnets on with the wrong polarity, I can turn the magnet inside the screen over without having to remove it from the pocket. Then I cut out the bottom magnet pockets. I only put one on each lower corner. We've had pretty good windstorms and rain and the covers haven't budged on our camper. Lastly I sewed the bottom pockets on - remembering to insert the magnet. I insert my awning pole or similar into the pocket and use it to lift my screens into place. The magnets snap together instantly all the way around the window. Then I pull it a bit to adjust it evenly. TA-DAH! Enjoy my view without the heat!! UPDATE: We had a strong windstorm and the screens stayed on perfectly! If you enjoy this blog or learn something from the article, please buy through my link and help me continue to bring you DIY ideas and tutorials. For those wondering how you would remove glued on magnets - Use fishing line to separate them from the fiberglass, Goo Gone to remove adhesive. Now Go Play Outside!
The astounding EarthRoamer SX is a recreational vehicle that can take on almost any terrain while offering the height of luxurious amenities.
Been looking for the best RV off grid solar system for you? This 50W solar panel will help start your camper solar setup. Get this to start your off grid solar trailer adventure today! Features 12V off-grid solar panel. 0~+5W guaranteed positive power output. IP 65 or IP 67 rated. Built with strong tempered glass and aluminum frame. Certified to withstand challenging environmental conditions. Excellent low light performance on cloudy days, mornings and evenings. Installation Easy installation and handling for various applications. Pre-drilled holes compatible with ground mounts, Z-brackets, pole mounts and tilt mounts. Compatible with on-grid and off-grid inverters. Warranty 25 years 80% output power. 5 years materials and workmanship. 1 year materials for accessories. Tech Specs Built-in Components RICH SOLAR 50 Watt Monocrystalline Solar Panel Panel Leads (Pair): 12AWG 2FT IP65 Rated waterproof junction box IP67 Rated waterproof solar connectors Specifications Maximum Power(Pmax): 50W Maximum Power Voltage(Vmp): 18.2V Maximum Power Current(Imp): 2.75A Open Circuit Voltage(Voc): 22.2V Short Circuit Current(Isc): 2.94A Maximum System Voltage(Vmax): 600VDC Weight: 8.2 lb Dimensions: 22.8x20.5x1.2in
\n DABBSSON Solar Generator 3500 is composed of Portable Power Station Dabs3500 and 1 packs Solar Panel 420W that aims to developing green, quiet and convenient energy solutions. Solar Generator 3500 is green for getting solar power without zero emission and nearly silent when in operation. Simply connect the solar panels to the power station, you can enjoy reliable power when you go RV camping or fishing. \nRecharge your power station at home, on the rooftop, in the yard, or on the go. All at lightning-fast speeds. 2400W Solar Charge to 100% in 2 Hrs. 120V-240V Power System With the ability to power up to 240V devices and an impressive output of up to 7000W, our units give you the freedom to conquer any power requirements from low to high wattages. By parallel connecting two Dabs3500 power stations and four Dabs5300B batteries, you can achieve a maximum capacity of 28,140Wh. Keep your entire home powered for up to a week.\n
Living in an RV full-time means we needed extra RV kitchen appliances. Check out our favorite RV kitchen appliances in this post!
Learn the best Solar Panels for an RV and whether permanent or portable solar panels are the best choice for your camping needs. Our list of top solar panels includes rigid solar panels, flexible solar panels, and portable solar panels and an RV solar panels kit. Use our Free Solar Calculator tool
![[GO POWER!] 220-Watt Flexible Solar Kit](https://i.pinimg.com/originals/ce/79/c8/ce79c80ea25fcef141a197138ccb018d.jpg)
The Go Power! 220-watt solar flex kit is perfect for RV’s and boats, its flexible design can conform to almost any surface. The panels are only 3 mm thick, making them easy to install. The thin, lightweight design provides a low profile, which is aesthetically pleasing and more aerodynamic than traditional rigid solar modules. The solar panels are durable, allowing a bend of up to 30°, providing you with a long-term solution to your solar power needs. An impermeable lamination coats the entire Solar Flex™ module, allowing it to contour and flex against curved surfaces, eliminating any need for custom mounts. The panel can be affixed by adhesive or screws, and grommets are provided for ease of installation. Product Overview MODEL: GP-FLEX-220 Key Benefits: Avoids custom mounts Can be installed on a curve up to 30 degrees Durable surface Measures less than 1/8” (3 mm) thick Is ideal for lightweight RVs (modules are 82% lighter) 5-year solar module power output warranty Please note that sealant/adhesive required will depend on roof membrane material and is not included in the Solar Flex kit. Use an appropriate sealant as recommended by your RV dealer or manufacturer. Kit Includes: 220 watts / 12.62 amps solar charging kit 30-amp single-bank, Bluetooth® PWM Solar Controller (GP-SB-PWM-30-BT)* 25′ of solar output cable - RED (#10) 25′ of solar output cable - BLACK (#10) *If you have the GP-PWM-30-UL controller WITH Bluetooth, please click here for the User Manual and Spec Sheet. *If you have the GP-PWM-30-UL controller WITHOUT Bluetooth, please click here for the User Manual and Spec Sheet. Please Note: shipping will be calculated and invoiced separately
HyperGear 13681 10,000 mAh Solar Power Bank Whether you re heading to a campground, beach, or just wandering around town, you need the HyperGear 10,000 mAh Solar Power Bank to stay connected. Not only does this portable battery pack offer a large 10,000 mAh capacity and 2 high-speed USB ports, it also features a compass, LED flashlight, and a built-in solar panel for emergency recharging! It s the ultimate backup power source for any adventure. What You Get HyperGear 13681 10,000 mAh Solar Power Bank Micro USB charging cable Carabiner User manual
Item specificsCondition
There are over 5,000 unique looking helical columns along the shoreline of Crowley Lake that can be accessed by paddling and by foot.
From solar panels, to charge controllers, leisure batteries, to our top recommendations - all you need for the ultimate 'off-grid' campervan solar living!
