Disclosure: We are a professional review site that receives compensation from the companies whose products we review. We test each product thoroughly and give
Fitting clothes into an RV can be tough. Here are some closet storage and organization ideas for different kinds of campers, motorhomes, or travel trailers.
Beat the heat! How I built solar screens on my RV windows. We've been in cooler regions of the United States this summer, so heat wasn't a problem -- but we had to come back to central Texas this month! Heat over 100 degrees! I made really nice adjustable, removable fabric awnings for my previous camper. (If you want to know how, click here) I liked them a lot, and they are super cute, but they have a couple drawbacks. If it gets really windy in the middle of the night, they will bang on the camper. Sometimes loudly enough that you have to get out of your cozy bed and put them away. It took a lot of time to make the awnings - making the solar shades take almost no time at all! So, I came up with the idea of solar screen covers for the windows. There are a lot of advantages. There is a video at the end of this article that shows how stable they are in a windstorm. They block up to 90% of the sun's heat. Unlike the silver stuff, you can see through your windows and don't feel like you're living in a cave. They are easy to put up and take down. You don't have to remove them if it rains or is windy. You can open and close all your windows, including the emergency window without removing them. You can have airflow through the trailer and still block the heat Best of all YOU CAN SEE OUTSIDE! The screens are held up with magnets and are easy to install and remove without a ladder. Interested? Read on to see how I did it! Note: all my affiliate links will generate money for your favorite charity! They are all set to go to smile.amazon.com To hold up the screens, I glued one magnet to the RV and sewed a matching magnet into the screen. There has been discussion about using snaps, but I didn't want to make holes in my camper. I can remove the magnets if I ever want to. This is what I used: Solar Screen (obviously) Magnets Normal Sewing Machine (I use a cheap Brother machine similar to this one that is AMAZING!) Heavy UV Resistant Thread These are the same size as the magnets I used. Plan on using a magnet about every 1-2 feet. My windows are small. The largest two are only about 48"'w x 24"h. If I had larger windows, I would have used larger magnets or more magnets closer together. On the 48-in windows I used 4 magnets across the top. On 36" windows I used 3 magnets across the top. On 24" windows I just put a magnet on each corner. Mostly your concerned about the weight of the screen fabric. If I had larger windows, these magnets would have worked better. Be VERY CAREFUL with the magnets, be VERY careful with them, they are extremely brittle. They will also give you a blood blister if they catch your finger between them. Once they are mounted on the RV wall, or sewn into a pocket they are pretty sturdy. It's just slamming together with no cushion that causes them to break. I cleaned the area around the windows with rubbing alcohol and stuck the magnets to the camper wall using the adhesive that was included with them. I measured the windows I wanted to cover, including the frame. Then I planned out how I was going to do it and how much screen I needed to buy. Yes, I admit I'm a bit detail-oriented about drawing out my plans and knowing exactly what I'm going to do before I start. This is the solar screen I used. I got mine at Lowe's for about $15 per roll. It took about 2 1/2 rolls. It blocks 90% of the radiant heat. It seems to work even if it's not in direct sun. If I bought the screen that blocks only 75% I could have cut my price in half. Amazon has some here. Cut pieces of solar screen about 1"-2" wider than the windows and 6-7" taller. It needs to have enough to fold over 2-3" and be long enough to cover from the magnets at the top to the bottom of the window, even longer if I was going to put magnets along the bottom of the window instead of just at each lower corner. Plain ol' school chalk marks the screens, it works great! Fold over and pin the top. I allowed 2" for the top hem/pockets. Fold and pin the 2" top hem/pockets. I sewed very close to the top edge to form a crease. I used a long straight stitch. I marked the approximate locations of the magnets and sewed a pocket about 3-5" wide for each magnet. Around each magnet pocket, I used a zig-zag stitch. Make sure to insert the magnets before sewing the final side :) This is similar to the sewing machine I have, which I bought at Sam's Club for $135 I DID NOT SEW THE WHOLE TOP FLAT - I left it open between the pockets. This is the trick to making them easy to install! I did not sew the bottom corner magnets until I test fit it to the window to mark exactly where they needed to be. I mounted the screen to the top magnets, pulled to make it even, used chalk to mark where the bottom edge of the window is, and where the magnets are. Remove the screen. Cut the screen about 1/2" - 1" below where I marked the bottom of the window. If I was putting magnets under the window, the screen would have needed to be longer. I can use my awning hook or WDH bar to push the screen up to attach to the magnets. This is why I made the magnet pockets large - so that I don't have to line it up perfectly when I am trying to install the screens. Also, if I mistakenly put one of my magnets on with the wrong polarity, I can turn the magnet inside the screen over without having to remove it from the pocket. Then I cut out the bottom magnet pockets. I only put one on each lower corner. We've had pretty good windstorms and rain and the covers haven't budged on our camper. Lastly I sewed the bottom pockets on - remembering to insert the magnet. I insert my awning pole or similar into the pocket and use it to lift my screens into place. The magnets snap together instantly all the way around the window. Then I pull it a bit to adjust it evenly. TA-DAH! Enjoy my view without the heat!! UPDATE: We had a strong windstorm and the screens stayed on perfectly! If you enjoy this blog or learn something from the article, please buy through my link and help me continue to bring you DIY ideas and tutorials. For those wondering how you would remove glued on magnets - Use fishing line to separate them from the fiberglass, Goo Gone to remove adhesive. Now Go Play Outside!
Trailer-sailors enjoy small sailboats. Some are open cockpit daysailers. Some are small live-aboard cabin cruisers. All are easy to rig, launch and retrieveand fun to sail.Every trailer-sailing family with a sailboat loves the idea that they can cruise their dreamboat to windward at 55mph in any direction they wish. Most of these boats can be stored in the family garage. Snowbound
Beat the heat! How I built solar screens on my RV windows. We've been in cooler regions of the United States this summer, so heat wasn't a problem -- but we had to come back to central Texas this month! Heat over 100 degrees! I made really nice adjustable, removable fabric awnings for my previous camper. (If you want to know how, click here) I liked them a lot, and they are super cute, but they have a couple drawbacks. If it gets really windy in the middle of the night, they will bang on the camper. Sometimes loudly enough that you have to get out of your cozy bed and put them away. It took a lot of time to make the awnings - making the solar shades take almost no time at all! So, I came up with the idea of solar screen covers for the windows. There are a lot of advantages. There is a video at the end of this article that shows how stable they are in a windstorm. They block up to 90% of the sun's heat. Unlike the silver stuff, you can see through your windows and don't feel like you're living in a cave. They are easy to put up and take down. You don't have to remove them if it rains or is windy. You can open and close all your windows, including the emergency window without removing them. You can have airflow through the trailer and still block the heat Best of all YOU CAN SEE OUTSIDE! The screens are held up with magnets and are easy to install and remove without a ladder. Interested? Read on to see how I did it! Note: all my affiliate links will generate money for your favorite charity! They are all set to go to smile.amazon.com To hold up the screens, I glued one magnet to the RV and sewed a matching magnet into the screen. There has been discussion about using snaps, but I didn't want to make holes in my camper. I can remove the magnets if I ever want to. This is what I used: Solar Screen (obviously) Magnets Normal Sewing Machine (I use a cheap Brother machine similar to this one that is AMAZING!) Heavy UV Resistant Thread These are the same size as the magnets I used. Plan on using a magnet about every 1-2 feet. My windows are small. The largest two are only about 48"'w x 24"h. If I had larger windows, I would have used larger magnets or more magnets closer together. On the 48-in windows I used 4 magnets across the top. On 36" windows I used 3 magnets across the top. On 24" windows I just put a magnet on each corner. Mostly your concerned about the weight of the screen fabric. If I had larger windows, these magnets would have worked better. Be VERY CAREFUL with the magnets, be VERY careful with them, they are extremely brittle. They will also give you a blood blister if they catch your finger between them. Once they are mounted on the RV wall, or sewn into a pocket they are pretty sturdy. It's just slamming together with no cushion that causes them to break. I cleaned the area around the windows with rubbing alcohol and stuck the magnets to the camper wall using the adhesive that was included with them. I measured the windows I wanted to cover, including the frame. Then I planned out how I was going to do it and how much screen I needed to buy. Yes, I admit I'm a bit detail-oriented about drawing out my plans and knowing exactly what I'm going to do before I start. This is the solar screen I used. I got mine at Lowe's for about $15 per roll. It took about 2 1/2 rolls. It blocks 90% of the radiant heat. It seems to work even if it's not in direct sun. If I bought the screen that blocks only 75% I could have cut my price in half. Amazon has some here. Cut pieces of solar screen about 1"-2" wider than the windows and 6-7" taller. It needs to have enough to fold over 2-3" and be long enough to cover from the magnets at the top to the bottom of the window, even longer if I was going to put magnets along the bottom of the window instead of just at each lower corner. Plain ol' school chalk marks the screens, it works great! Fold over and pin the top. I allowed 2" for the top hem/pockets. Fold and pin the 2" top hem/pockets. I sewed very close to the top edge to form a crease. I used a long straight stitch. I marked the approximate locations of the magnets and sewed a pocket about 3-5" wide for each magnet. Around each magnet pocket, I used a zig-zag stitch. Make sure to insert the magnets before sewing the final side :) This is similar to the sewing machine I have, which I bought at Sam's Club for $135 I DID NOT SEW THE WHOLE TOP FLAT - I left it open between the pockets. This is the trick to making them easy to install! I did not sew the bottom corner magnets until I test fit it to the window to mark exactly where they needed to be. I mounted the screen to the top magnets, pulled to make it even, used chalk to mark where the bottom edge of the window is, and where the magnets are. Remove the screen. Cut the screen about 1/2" - 1" below where I marked the bottom of the window. If I was putting magnets under the window, the screen would have needed to be longer. I can use my awning hook or WDH bar to push the screen up to attach to the magnets. This is why I made the magnet pockets large - so that I don't have to line it up perfectly when I am trying to install the screens. Also, if I mistakenly put one of my magnets on with the wrong polarity, I can turn the magnet inside the screen over without having to remove it from the pocket. Then I cut out the bottom magnet pockets. I only put one on each lower corner. We've had pretty good windstorms and rain and the covers haven't budged on our camper. Lastly I sewed the bottom pockets on - remembering to insert the magnet. I insert my awning pole or similar into the pocket and use it to lift my screens into place. The magnets snap together instantly all the way around the window. Then I pull it a bit to adjust it evenly. TA-DAH! Enjoy my view without the heat!! UPDATE: We had a strong windstorm and the screens stayed on perfectly! If you enjoy this blog or learn something from the article, please buy through my link and help me continue to bring you DIY ideas and tutorials. For those wondering how you would remove glued on magnets - Use fishing line to separate them from the fiberglass, Goo Gone to remove adhesive. Now Go Play Outside!
When it comes to creating the wow factor for your boat, the interior is just as important as the exterior. And if you’re looking for inspiration, you’ve come to the right place! We’re going to look at 27 boat interior ideas to create comfort and visual impact in any kind of space. And there are...
JUMP TO A SECTION... Top 10 Dos For Patio Shade Sails (1-10)1. DO track the sun. 2. DO measure the area you want to shade. 3. DO find anchor points. 4. DO take time to make proper measurements. 5. DO make sure your anchor points are structurally sound. 6. DO slope your shade sail. 7. […]
JUMP TO A SECTION... Top 10 Dos For Patio Shade Sails (1-10)1. DO track the sun. 2. DO measure the area you want to shade. 3. DO find anchor points. 4. DO take time to make proper measurements. 5. DO make sure your anchor points are structurally sound. 6. DO slope your shade sail. 7. […]
Beat the heat! How I built solar screens on my RV windows. We've been in cooler regions of the United States this summer, so heat wasn't a problem -- but we had to come back to central Texas this month! Heat over 100 degrees! I made really nice adjustable, removable fabric awnings for my previous camper. (If you want to know how, click here) I liked them a lot, and they are super cute, but they have a couple drawbacks. If it gets really windy in the middle of the night, they will bang on the camper. Sometimes loudly enough that you have to get out of your cozy bed and put them away. It took a lot of time to make the awnings - making the solar shades take almost no time at all! So, I came up with the idea of solar screen covers for the windows. There are a lot of advantages. There is a video at the end of this article that shows how stable they are in a windstorm. They block up to 90% of the sun's heat. Unlike the silver stuff, you can see through your windows and don't feel like you're living in a cave. They are easy to put up and take down. You don't have to remove them if it rains or is windy. You can open and close all your windows, including the emergency window without removing them. You can have airflow through the trailer and still block the heat Best of all YOU CAN SEE OUTSIDE! The screens are held up with magnets and are easy to install and remove without a ladder. Interested? Read on to see how I did it! Note: all my affiliate links will generate money for your favorite charity! They are all set to go to smile.amazon.com To hold up the screens, I glued one magnet to the RV and sewed a matching magnet into the screen. There has been discussion about using snaps, but I didn't want to make holes in my camper. I can remove the magnets if I ever want to. This is what I used: Solar Screen (obviously) Magnets Normal Sewing Machine (I use a cheap Brother machine similar to this one that is AMAZING!) Heavy UV Resistant Thread These are the same size as the magnets I used. Plan on using a magnet about every 1-2 feet. My windows are small. The largest two are only about 48"'w x 24"h. If I had larger windows, I would have used larger magnets or more magnets closer together. On the 48-in windows I used 4 magnets across the top. On 36" windows I used 3 magnets across the top. On 24" windows I just put a magnet on each corner. Mostly your concerned about the weight of the screen fabric. If I had larger windows, these magnets would have worked better. Be VERY CAREFUL with the magnets, be VERY careful with them, they are extremely brittle. They will also give you a blood blister if they catch your finger between them. Once they are mounted on the RV wall, or sewn into a pocket they are pretty sturdy. It's just slamming together with no cushion that causes them to break. I cleaned the area around the windows with rubbing alcohol and stuck the magnets to the camper wall using the adhesive that was included with them. I measured the windows I wanted to cover, including the frame. Then I planned out how I was going to do it and how much screen I needed to buy. Yes, I admit I'm a bit detail-oriented about drawing out my plans and knowing exactly what I'm going to do before I start. This is the solar screen I used. I got mine at Lowe's for about $15 per roll. It took about 2 1/2 rolls. It blocks 90% of the radiant heat. It seems to work even if it's not in direct sun. If I bought the screen that blocks only 75% I could have cut my price in half. Amazon has some here. Cut pieces of solar screen about 1"-2" wider than the windows and 6-7" taller. It needs to have enough to fold over 2-3" and be long enough to cover from the magnets at the top to the bottom of the window, even longer if I was going to put magnets along the bottom of the window instead of just at each lower corner. Plain ol' school chalk marks the screens, it works great! Fold over and pin the top. I allowed 2" for the top hem/pockets. Fold and pin the 2" top hem/pockets. I sewed very close to the top edge to form a crease. I used a long straight stitch. I marked the approximate locations of the magnets and sewed a pocket about 3-5" wide for each magnet. Around each magnet pocket, I used a zig-zag stitch. Make sure to insert the magnets before sewing the final side :) This is similar to the sewing machine I have, which I bought at Sam's Club for $135 I DID NOT SEW THE WHOLE TOP FLAT - I left it open between the pockets. This is the trick to making them easy to install! I did not sew the bottom corner magnets until I test fit it to the window to mark exactly where they needed to be. I mounted the screen to the top magnets, pulled to make it even, used chalk to mark where the bottom edge of the window is, and where the magnets are. Remove the screen. Cut the screen about 1/2" - 1" below where I marked the bottom of the window. If I was putting magnets under the window, the screen would have needed to be longer. I can use my awning hook or WDH bar to push the screen up to attach to the magnets. This is why I made the magnet pockets large - so that I don't have to line it up perfectly when I am trying to install the screens. Also, if I mistakenly put one of my magnets on with the wrong polarity, I can turn the magnet inside the screen over without having to remove it from the pocket. Then I cut out the bottom magnet pockets. I only put one on each lower corner. We've had pretty good windstorms and rain and the covers haven't budged on our camper. Lastly I sewed the bottom pockets on - remembering to insert the magnet. I insert my awning pole or similar into the pocket and use it to lift my screens into place. The magnets snap together instantly all the way around the window. Then I pull it a bit to adjust it evenly. TA-DAH! Enjoy my view without the heat!! UPDATE: We had a strong windstorm and the screens stayed on perfectly! If you enjoy this blog or learn something from the article, please buy through my link and help me continue to bring you DIY ideas and tutorials. For those wondering how you would remove glued on magnets - Use fishing line to separate them from the fiberglass, Goo Gone to remove adhesive. Now Go Play Outside!
When you are looking at setting up the right type of shade in the yard, the one option you are going to want to think about will be a sun sail shade setup.
There are several easy, common-sense steps to protect your boat and everyone on board. Here are a few of the most important.
Beat the heat! How I built solar screens on my RV windows. We've been in cooler regions of the United States this summer, so heat wasn't a problem -- but we had to come back to central Texas this month! Heat over 100 degrees! I made really nice adjustable, removable fabric awnings for my previous camper. (If you want to know how, click here) I liked them a lot, and they are super cute, but they have a couple drawbacks. If it gets really windy in the middle of the night, they will bang on the camper. Sometimes loudly enough that you have to get out of your cozy bed and put them away. It took a lot of time to make the awnings - making the solar shades take almost no time at all! So, I came up with the idea of solar screen covers for the windows. There are a lot of advantages. There is a video at the end of this article that shows how stable they are in a windstorm. They block up to 90% of the sun's heat. Unlike the silver stuff, you can see through your windows and don't feel like you're living in a cave. They are easy to put up and take down. You don't have to remove them if it rains or is windy. You can open and close all your windows, including the emergency window without removing them. You can have airflow through the trailer and still block the heat Best of all YOU CAN SEE OUTSIDE! The screens are held up with magnets and are easy to install and remove without a ladder. Interested? Read on to see how I did it! Note: all my affiliate links will generate money for your favorite charity! They are all set to go to smile.amazon.com To hold up the screens, I glued one magnet to the RV and sewed a matching magnet into the screen. There has been discussion about using snaps, but I didn't want to make holes in my camper. I can remove the magnets if I ever want to. This is what I used: Solar Screen (obviously) Magnets Normal Sewing Machine (I use a cheap Brother machine similar to this one that is AMAZING!) Heavy UV Resistant Thread These are the same size as the magnets I used. Plan on using a magnet about every 1-2 feet. My windows are small. The largest two are only about 48"'w x 24"h. If I had larger windows, I would have used larger magnets or more magnets closer together. On the 48-in windows I used 4 magnets across the top. On 36" windows I used 3 magnets across the top. On 24" windows I just put a magnet on each corner. Mostly your concerned about the weight of the screen fabric. If I had larger windows, these magnets would have worked better. Be VERY CAREFUL with the magnets, be VERY careful with them, they are extremely brittle. They will also give you a blood blister if they catch your finger between them. Once they are mounted on the RV wall, or sewn into a pocket they are pretty sturdy. It's just slamming together with no cushion that causes them to break. I cleaned the area around the windows with rubbing alcohol and stuck the magnets to the camper wall using the adhesive that was included with them. I measured the windows I wanted to cover, including the frame. Then I planned out how I was going to do it and how much screen I needed to buy. Yes, I admit I'm a bit detail-oriented about drawing out my plans and knowing exactly what I'm going to do before I start. This is the solar screen I used. I got mine at Lowe's for about $15 per roll. It took about 2 1/2 rolls. It blocks 90% of the radiant heat. It seems to work even if it's not in direct sun. If I bought the screen that blocks only 75% I could have cut my price in half. Amazon has some here. Cut pieces of solar screen about 1"-2" wider than the windows and 6-7" taller. It needs to have enough to fold over 2-3" and be long enough to cover from the magnets at the top to the bottom of the window, even longer if I was going to put magnets along the bottom of the window instead of just at each lower corner. Plain ol' school chalk marks the screens, it works great! Fold over and pin the top. I allowed 2" for the top hem/pockets. Fold and pin the 2" top hem/pockets. I sewed very close to the top edge to form a crease. I used a long straight stitch. I marked the approximate locations of the magnets and sewed a pocket about 3-5" wide for each magnet. Around each magnet pocket, I used a zig-zag stitch. Make sure to insert the magnets before sewing the final side :) This is similar to the sewing machine I have, which I bought at Sam's Club for $135 I DID NOT SEW THE WHOLE TOP FLAT - I left it open between the pockets. This is the trick to making them easy to install! I did not sew the bottom corner magnets until I test fit it to the window to mark exactly where they needed to be. I mounted the screen to the top magnets, pulled to make it even, used chalk to mark where the bottom edge of the window is, and where the magnets are. Remove the screen. Cut the screen about 1/2" - 1" below where I marked the bottom of the window. If I was putting magnets under the window, the screen would have needed to be longer. I can use my awning hook or WDH bar to push the screen up to attach to the magnets. This is why I made the magnet pockets large - so that I don't have to line it up perfectly when I am trying to install the screens. Also, if I mistakenly put one of my magnets on with the wrong polarity, I can turn the magnet inside the screen over without having to remove it from the pocket. Then I cut out the bottom magnet pockets. I only put one on each lower corner. We've had pretty good windstorms and rain and the covers haven't budged on our camper. Lastly I sewed the bottom pockets on - remembering to insert the magnet. I insert my awning pole or similar into the pocket and use it to lift my screens into place. The magnets snap together instantly all the way around the window. Then I pull it a bit to adjust it evenly. TA-DAH! Enjoy my view without the heat!! UPDATE: We had a strong windstorm and the screens stayed on perfectly! If you enjoy this blog or learn something from the article, please buy through my link and help me continue to bring you DIY ideas and tutorials. For those wondering how you would remove glued on magnets - Use fishing line to separate them from the fiberglass, Goo Gone to remove adhesive. Now Go Play Outside!
Traveling by sailboat or RV allows you to explore with the convenience of taking your home with you.
Add instant shade for not a lot of money and just a little bit of elbow grease by hanging a triangular shade cover over your patio or deck.
From pristine beaches and crystal clear water to boulders, caves, fresh seafood, and delicious umbrella drinks...this is The British Virgin Islands.
Beat the heat! How I built solar screens on my RV windows. We've been in cooler regions of the United States this summer, so heat wasn't a problem -- but we had to come back to central Texas this month! Heat over 100 degrees! I made really nice adjustable, removable fabric awnings for my previous camper. (If you want to know how, click here) I liked them a lot, and they are super cute, but they have a couple drawbacks. If it gets really windy in the middle of the night, they will bang on the camper. Sometimes loudly enough that you have to get out of your cozy bed and put them away. It took a lot of time to make the awnings - making the solar shades take almost no time at all! So, I came up with the idea of solar screen covers for the windows. There are a lot of advantages. There is a video at the end of this article that shows how stable they are in a windstorm. They block up to 90% of the sun's heat. Unlike the silver stuff, you can see through your windows and don't feel like you're living in a cave. They are easy to put up and take down. You don't have to remove them if it rains or is windy. You can open and close all your windows, including the emergency window without removing them. You can have airflow through the trailer and still block the heat Best of all YOU CAN SEE OUTSIDE! The screens are held up with magnets and are easy to install and remove without a ladder. Interested? Read on to see how I did it! Note: all my affiliate links will generate money for your favorite charity! They are all set to go to smile.amazon.com To hold up the screens, I glued one magnet to the RV and sewed a matching magnet into the screen. There has been discussion about using snaps, but I didn't want to make holes in my camper. I can remove the magnets if I ever want to. This is what I used: Solar Screen (obviously) Magnets Normal Sewing Machine (I use a cheap Brother machine similar to this one that is AMAZING!) Heavy UV Resistant Thread These are the same size as the magnets I used. Plan on using a magnet about every 1-2 feet. My windows are small. The largest two are only about 48"'w x 24"h. If I had larger windows, I would have used larger magnets or more magnets closer together. On the 48-in windows I used 4 magnets across the top. On 36" windows I used 3 magnets across the top. On 24" windows I just put a magnet on each corner. Mostly your concerned about the weight of the screen fabric. If I had larger windows, these magnets would have worked better. Be VERY CAREFUL with the magnets, be VERY careful with them, they are extremely brittle. They will also give you a blood blister if they catch your finger between them. Once they are mounted on the RV wall, or sewn into a pocket they are pretty sturdy. It's just slamming together with no cushion that causes them to break. I cleaned the area around the windows with rubbing alcohol and stuck the magnets to the camper wall using the adhesive that was included with them. I measured the windows I wanted to cover, including the frame. Then I planned out how I was going to do it and how much screen I needed to buy. Yes, I admit I'm a bit detail-oriented about drawing out my plans and knowing exactly what I'm going to do before I start. This is the solar screen I used. I got mine at Lowe's for about $15 per roll. It took about 2 1/2 rolls. It blocks 90% of the radiant heat. It seems to work even if it's not in direct sun. If I bought the screen that blocks only 75% I could have cut my price in half. Amazon has some here. Cut pieces of solar screen about 1"-2" wider than the windows and 6-7" taller. It needs to have enough to fold over 2-3" and be long enough to cover from the magnets at the top to the bottom of the window, even longer if I was going to put magnets along the bottom of the window instead of just at each lower corner. Plain ol' school chalk marks the screens, it works great! Fold over and pin the top. I allowed 2" for the top hem/pockets. Fold and pin the 2" top hem/pockets. I sewed very close to the top edge to form a crease. I used a long straight stitch. I marked the approximate locations of the magnets and sewed a pocket about 3-5" wide for each magnet. Around each magnet pocket, I used a zig-zag stitch. Make sure to insert the magnets before sewing the final side :) This is similar to the sewing machine I have, which I bought at Sam's Club for $135 I DID NOT SEW THE WHOLE TOP FLAT - I left it open between the pockets. This is the trick to making them easy to install! I did not sew the bottom corner magnets until I test fit it to the window to mark exactly where they needed to be. I mounted the screen to the top magnets, pulled to make it even, used chalk to mark where the bottom edge of the window is, and where the magnets are. Remove the screen. Cut the screen about 1/2" - 1" below where I marked the bottom of the window. If I was putting magnets under the window, the screen would have needed to be longer. I can use my awning hook or WDH bar to push the screen up to attach to the magnets. This is why I made the magnet pockets large - so that I don't have to line it up perfectly when I am trying to install the screens. Also, if I mistakenly put one of my magnets on with the wrong polarity, I can turn the magnet inside the screen over without having to remove it from the pocket. Then I cut out the bottom magnet pockets. I only put one on each lower corner. We've had pretty good windstorms and rain and the covers haven't budged on our camper. Lastly I sewed the bottom pockets on - remembering to insert the magnet. I insert my awning pole or similar into the pocket and use it to lift my screens into place. The magnets snap together instantly all the way around the window. Then I pull it a bit to adjust it evenly. TA-DAH! Enjoy my view without the heat!! UPDATE: We had a strong windstorm and the screens stayed on perfectly! If you enjoy this blog or learn something from the article, please buy through my link and help me continue to bring you DIY ideas and tutorials. For those wondering how you would remove glued on magnets - Use fishing line to separate them from the fiberglass, Goo Gone to remove adhesive. Now Go Play Outside!
Is the Arvika RV bike rack the best RV bike carrier? We love camping & bicycling and this 7000 series rack works great. Check out our Arvika bike rack review.
Add instant shade for not a lot of money and just a little bit of elbow grease by hanging a triangular shade cover over your patio or deck.
Looking for the best campsites in Florida? Here are our top 10 best campgrounds in Florida that offer a memorable camping experience in Key West and Gulf Coast
Beat the heat! How I built solar screens on my RV windows. We've been in cooler regions of the United States this summer, so heat wasn't a problem -- but we had to come back to central Texas this month! Heat over 100 degrees! I made really nice adjustable, removable fabric awnings for my previous camper. (If you want to know how, click here) I liked them a lot, and they are super cute, but they have a couple drawbacks. If it gets really windy in the middle of the night, they will bang on the camper. Sometimes loudly enough that you have to get out of your cozy bed and put them away. It took a lot of time to make the awnings - making the solar shades take almost no time at all! So, I came up with the idea of solar screen covers for the windows. There are a lot of advantages. There is a video at the end of this article that shows how stable they are in a windstorm. They block up to 90% of the sun's heat. Unlike the silver stuff, you can see through your windows and don't feel like you're living in a cave. They are easy to put up and take down. You don't have to remove them if it rains or is windy. You can open and close all your windows, including the emergency window without removing them. You can have airflow through the trailer and still block the heat Best of all YOU CAN SEE OUTSIDE! The screens are held up with magnets and are easy to install and remove without a ladder. Interested? Read on to see how I did it! Note: all my affiliate links will generate money for your favorite charity! They are all set to go to smile.amazon.com To hold up the screens, I glued one magnet to the RV and sewed a matching magnet into the screen. There has been discussion about using snaps, but I didn't want to make holes in my camper. I can remove the magnets if I ever want to. This is what I used: Solar Screen (obviously) Magnets Normal Sewing Machine (I use a cheap Brother machine similar to this one that is AMAZING!) Heavy UV Resistant Thread These are the same size as the magnets I used. Plan on using a magnet about every 1-2 feet. My windows are small. The largest two are only about 48"'w x 24"h. If I had larger windows, I would have used larger magnets or more magnets closer together. On the 48-in windows I used 4 magnets across the top. On 36" windows I used 3 magnets across the top. On 24" windows I just put a magnet on each corner. Mostly your concerned about the weight of the screen fabric. If I had larger windows, these magnets would have worked better. Be VERY CAREFUL with the magnets, be VERY careful with them, they are extremely brittle. They will also give you a blood blister if they catch your finger between them. Once they are mounted on the RV wall, or sewn into a pocket they are pretty sturdy. It's just slamming together with no cushion that causes them to break. I cleaned the area around the windows with rubbing alcohol and stuck the magnets to the camper wall using the adhesive that was included with them. I measured the windows I wanted to cover, including the frame. Then I planned out how I was going to do it and how much screen I needed to buy. Yes, I admit I'm a bit detail-oriented about drawing out my plans and knowing exactly what I'm going to do before I start. This is the solar screen I used. I got mine at Lowe's for about $15 per roll. It took about 2 1/2 rolls. It blocks 90% of the radiant heat. It seems to work even if it's not in direct sun. If I bought the screen that blocks only 75% I could have cut my price in half. Amazon has some here. Cut pieces of solar screen about 1"-2" wider than the windows and 6-7" taller. It needs to have enough to fold over 2-3" and be long enough to cover from the magnets at the top to the bottom of the window, even longer if I was going to put magnets along the bottom of the window instead of just at each lower corner. Plain ol' school chalk marks the screens, it works great! Fold over and pin the top. I allowed 2" for the top hem/pockets. Fold and pin the 2" top hem/pockets. I sewed very close to the top edge to form a crease. I used a long straight stitch. I marked the approximate locations of the magnets and sewed a pocket about 3-5" wide for each magnet. Around each magnet pocket, I used a zig-zag stitch. Make sure to insert the magnets before sewing the final side :) This is similar to the sewing machine I have, which I bought at Sam's Club for $135 I DID NOT SEW THE WHOLE TOP FLAT - I left it open between the pockets. This is the trick to making them easy to install! I did not sew the bottom corner magnets until I test fit it to the window to mark exactly where they needed to be. I mounted the screen to the top magnets, pulled to make it even, used chalk to mark where the bottom edge of the window is, and where the magnets are. Remove the screen. Cut the screen about 1/2" - 1" below where I marked the bottom of the window. If I was putting magnets under the window, the screen would have needed to be longer. I can use my awning hook or WDH bar to push the screen up to attach to the magnets. This is why I made the magnet pockets large - so that I don't have to line it up perfectly when I am trying to install the screens. Also, if I mistakenly put one of my magnets on with the wrong polarity, I can turn the magnet inside the screen over without having to remove it from the pocket. Then I cut out the bottom magnet pockets. I only put one on each lower corner. We've had pretty good windstorms and rain and the covers haven't budged on our camper. Lastly I sewed the bottom pockets on - remembering to insert the magnet. I insert my awning pole or similar into the pocket and use it to lift my screens into place. The magnets snap together instantly all the way around the window. Then I pull it a bit to adjust it evenly. TA-DAH! Enjoy my view without the heat!! UPDATE: We had a strong windstorm and the screens stayed on perfectly! If you enjoy this blog or learn something from the article, please buy through my link and help me continue to bring you DIY ideas and tutorials. For those wondering how you would remove glued on magnets - Use fishing line to separate them from the fiberglass, Goo Gone to remove adhesive. Now Go Play Outside!
Beat the heat! How I built solar screens on my RV windows. We've been in cooler regions of the United States this summer, so heat wasn't a problem -- but we had to come back to central Texas this month! Heat over 100 degrees! I made really nice adjustable, removable fabric awnings for my previous camper. (If you want to know how, click here) I liked them a lot, and they are super cute, but they have a couple drawbacks. If it gets really windy in the middle of the night, they will bang on the camper. Sometimes loudly enough that you have to get out of your cozy bed and put them away. It took a lot of time to make the awnings - making the solar shades take almost no time at all! So, I came up with the idea of solar screen covers for the windows. There are a lot of advantages. There is a video at the end of this article that shows how stable they are in a windstorm. They block up to 90% of the sun's heat. Unlike the silver stuff, you can see through your windows and don't feel like you're living in a cave. They are easy to put up and take down. You don't have to remove them if it rains or is windy. You can open and close all your windows, including the emergency window without removing them. You can have airflow through the trailer and still block the heat Best of all YOU CAN SEE OUTSIDE! The screens are held up with magnets and are easy to install and remove without a ladder. Interested? Read on to see how I did it! Note: all my affiliate links will generate money for your favorite charity! They are all set to go to smile.amazon.com To hold up the screens, I glued one magnet to the RV and sewed a matching magnet into the screen. There has been discussion about using snaps, but I didn't want to make holes in my camper. I can remove the magnets if I ever want to. This is what I used: Solar Screen (obviously) Magnets Normal Sewing Machine (I use a cheap Brother machine similar to this one that is AMAZING!) Heavy UV Resistant Thread These are the same size as the magnets I used. Plan on using a magnet about every 1-2 feet. My windows are small. The largest two are only about 48"'w x 24"h. If I had larger windows, I would have used larger magnets or more magnets closer together. On the 48-in windows I used 4 magnets across the top. On 36" windows I used 3 magnets across the top. On 24" windows I just put a magnet on each corner. Mostly your concerned about the weight of the screen fabric. If I had larger windows, these magnets would have worked better. Be VERY CAREFUL with the magnets, be VERY careful with them, they are extremely brittle. They will also give you a blood blister if they catch your finger between them. Once they are mounted on the RV wall, or sewn into a pocket they are pretty sturdy. It's just slamming together with no cushion that causes them to break. I cleaned the area around the windows with rubbing alcohol and stuck the magnets to the camper wall using the adhesive that was included with them. I measured the windows I wanted to cover, including the frame. Then I planned out how I was going to do it and how much screen I needed to buy. Yes, I admit I'm a bit detail-oriented about drawing out my plans and knowing exactly what I'm going to do before I start. This is the solar screen I used. I got mine at Lowe's for about $15 per roll. It took about 2 1/2 rolls. It blocks 90% of the radiant heat. It seems to work even if it's not in direct sun. If I bought the screen that blocks only 75% I could have cut my price in half. Amazon has some here. Cut pieces of solar screen about 1"-2" wider than the windows and 6-7" taller. It needs to have enough to fold over 2-3" and be long enough to cover from the magnets at the top to the bottom of the window, even longer if I was going to put magnets along the bottom of the window instead of just at each lower corner. Plain ol' school chalk marks the screens, it works great! Fold over and pin the top. I allowed 2" for the top hem/pockets. Fold and pin the 2" top hem/pockets. I sewed very close to the top edge to form a crease. I used a long straight stitch. I marked the approximate locations of the magnets and sewed a pocket about 3-5" wide for each magnet. Around each magnet pocket, I used a zig-zag stitch. Make sure to insert the magnets before sewing the final side :) This is similar to the sewing machine I have, which I bought at Sam's Club for $135 I DID NOT SEW THE WHOLE TOP FLAT - I left it open between the pockets. This is the trick to making them easy to install! I did not sew the bottom corner magnets until I test fit it to the window to mark exactly where they needed to be. I mounted the screen to the top magnets, pulled to make it even, used chalk to mark where the bottom edge of the window is, and where the magnets are. Remove the screen. Cut the screen about 1/2" - 1" below where I marked the bottom of the window. If I was putting magnets under the window, the screen would have needed to be longer. I can use my awning hook or WDH bar to push the screen up to attach to the magnets. This is why I made the magnet pockets large - so that I don't have to line it up perfectly when I am trying to install the screens. Also, if I mistakenly put one of my magnets on with the wrong polarity, I can turn the magnet inside the screen over without having to remove it from the pocket. Then I cut out the bottom magnet pockets. I only put one on each lower corner. We've had pretty good windstorms and rain and the covers haven't budged on our camper. Lastly I sewed the bottom pockets on - remembering to insert the magnet. I insert my awning pole or similar into the pocket and use it to lift my screens into place. The magnets snap together instantly all the way around the window. Then I pull it a bit to adjust it evenly. TA-DAH! Enjoy my view without the heat!! UPDATE: We had a strong windstorm and the screens stayed on perfectly! If you enjoy this blog or learn something from the article, please buy through my link and help me continue to bring you DIY ideas and tutorials. For those wondering how you would remove glued on magnets - Use fishing line to separate them from the fiberglass, Goo Gone to remove adhesive. Now Go Play Outside!
Navigation is the number one cause of stress between couples that travel or live full-time in an RV.