If you purchased this toy and would like to add a second or more additional color to this toy, please visit our store for additional color items: https://www.etsy.com/listing/1308729700/extra-colors-for-toys-add-color-to-item All of our toys are poured with 100% platinum cure silicone. This type of silicone is the highest grade material and is odorless and non-toxic for medical use. Platinum silicone is also non-porous, hypoallergenic and easy to clean. 100% Discreet Shipping Approximate Measurements: Small: Diameter: 1.5” / 3.8 cm, height(Highest): 0.8” / 2 cm, Weight: 19 g / 0.7 oz Medium: Diameter: 2” / 5.2 cm, height(Highest): 1.1” / 2.9 cm, Weight: 46 g / 1.6 oz Large: Diameter: 2.8” / 7.2 cm, height(Highest): 1.7” / 4.2 cm, Weight: 122 g / 4.3 oz Firmness: Medium Super Soft Shore 00-20 Rating With this tool, you can temporarily attach each toy with a flat base to any smooth surface. Add a little water before, press it, and it's ready to use! Check out our store - Plutoying.etsy.com Please note： 1.Because it is handmade, the product will not be exactly the same as the picture, but it is basically the same. 2. we are not responsible for any issues that arise from an order being purchased with the wrong shipping address. 3 Due to the brightness of the monitor and light brightness, the real color maybe a little different from the pictures shown on the product page. Hope you understand. Logistics query URL: https://www.17track.net/en

Silicone Rubber - Polytek Platsil - Liquid Silicone Platinum Cured Polytek® manufactures a full range of two-part, room-temperature curing silicone rubbers that offer great flexibility, tear strength, chemical resistance, and release properties. Silicone molds can be used to cast a variety of materials, including polyurethane, polyester and epoxy resins, polyurethane foam, plaster, wax, concrete, low melting metals, and more. One of the primary advantages of using silicone mold rubbers instead of other flexible materials, like polyurethane rubber, is that release agent is not needed when casting polyurethane resins, foams and other materials into silicone molds. This is especially important when cast parts need to be painted as paint will not adhere well to parts with residual release agent. **We often get asked how much is in a kit, and the answer is below under each product's 'Specific Volume'-- But, to simplify, if 1lb of material has a volume of 25 cubic inches, that is just under the size of a 3" x 3" x 3" cube, which is 27 cubic inches (picture a Rubik's Cube) Polytek® manufactures two different types of silicone rubbers: platinum-cured (PlatSil®) silicones and tin-cured (TinSil®) silicones:  There are distinct qualities that each line offers and their primary differences are:  TinSil® silicones are condensation-cure systems that shrink slightly on cure (~1%) compared to addition-cure PlatSil® silicones, which do not shrink on cure.  Cured TinSil® silicones have shorter library life (2 to 5 years total) compared to PlatSil® silicones. TinSil® silicones are slightly less expensive than PlatSil® silicones.  Liquid PlatSil® silicones are more sensitive to certain materials (e.g., sulfur, tin compounds, Bondo) and suffer from cure inhibition (uncured surface material) more often than TinSil® silicones. Cured TinSil® molds can inhibit some casting materials, including PlatSil® silicones, Poly-Optic® Clear Casting Resin and many polyurethane rubbers. There are skin-safe platinum-cured silicones available in the PlatSil® product line: PlatSil® Gels.      PlatSil (Plastinum Care) Silicone Rubber: Use PlatSil® Liquid Silicone Rubbers to make your own silicone molds and silicone parts. PlatSil® rubbers are platinum-cured (also known as addition-cure), room temperature-curing silicones (RTV) that are used to make flexible, high-strength molds and parts. PlatSil® molds are often selected over other mold materials (e.g., polyurethane rubbers) because of their excellent release properties. They also exhibit long library life and low shrinkage on cure compared to other mold material options. PlatSil® molds are excellent for casting polyurethane, epoxy and polyester resin, polyurethane foam, wax, plaster, soap, concrete, and more. Release agent is generally not needed to cast any of these materials. These rubbers are commonly used in Sculpture & Foundry, Prototyping, Architectural Reproduction & Restoration, Foam, Plastic & Plaster Millwork & Ornamentation, Theming & Display, Candle Making, Craft & Hobby projects, and some Concrete Casting applications. PlatSil Features: Two-part platinum-cured (addition-cure) silicone rubbers Room temperature curing (RTV) Shore Hardness Options: A10-A60 Do not exhibit shrinkage upon curing so they are useful for casting dimensionally stable parts for highly accurate prototyping and model making applications Molds do not require release agents when casting most materials Cured molds have a long library life Pourable or brushable (thicken with PlatThix liquid thickener or Fumed Silica) High-strength Excellent chemical resistance Reproduces fine details Can be accelerated for rapid cure Ideal for the most demanding resin casting applications NOTE ON CURE INHIBITION: Sulfur/tin/amine-contaminated materials and tools will cause cure inhibition in platinum-cured silicone rubbers, which means that the rubber that is in contact with the contaminated surface will remain gummy or uncured. Make sure to test cure the rubber on your surface before full-scale application. Use a polyurethane or tin-cured silicone rubber if you know that you’ll be working with any of these inhibitors. PlatSil® 71 & 73-Series Silicone Rubbers Listed below in order of hardness (softest at top).  Standard, platinum-cured mold making and casting silicone rubbers. PlatSil® 71 & 73-Series Technical Bulletin (TDS) PlatSil® FS-Series Technical Bulletin (TDS) PlatSil® Gel Series Technical Bulletin (TDS) PlatSil® Safety Data Sheet (SDS) PlatSil® FS-Series Safety Data Sheet (SDS) Product Mix Ratio by Weight Shore Hardness Pour Time Demold Time Cured Color Specific Volume Mixed Viscosity Shrinkage Upon Cure PlatSil® 71-11 1A:1B A10 20 min. 4 hr. Blue-Green 24.7 in³/lb 6,000 cP Nil PlatSil® 73-15 1A:1B A15 20 min. 4-5 hr. White Translucent 25.0 in³/lb 2,500 cP Nil PlatSil® 73-20 1A:1B A22 5 min. 1 hr. Blue Translucent 25.0 in³/lb 3,000 cP Nil PlatSil® 71-25 1A:1B A25 35 min. 16 hr. Milky White 25.0 in³/lb 3,500 cP Nil PlatSil® 73-25 1A:1B A25 15 min. 4-5 hr. Green 24.3 in³/lb 6,000 cP Nil PlatSil® 73-29 1A:10B A30 45 min. 16 hr. White 25.0 in³/lb 15,000 cP Nil PlatSil® 71-40 1A:10B A40 90 min. 24 hr. Translucent 26.6 in³/lb 38,000 cP Nil PlatSil® 73-40 1A:10B A40 45 min. 16 hr. Yellow 22.0 in³/lb 25,000 cP Nil PlatSil® 73-45 1A:10B A45 40 min. 16 hr. Green 21.3 in³/lb 35.000 cP Nil PlatSil® 73-60 1A:10B A60 45 min. 16 hr. Blue 21.3 in³/lb 40,000 cP Nil PlatSil® FS-10 1A:1B OO60/A13 8 min. 25 min. Milky White 24.9 in³/lb 4,200 cP Nil PlatSil® FS-20 1A:1B OO66/A20 8 min. 25 min. Milky White 24.9 in³/lb 3,800 cP Nil PlatSil® HTS-25 1A:10B A25 70 min. 24 hr. Milky White 24.9 in³/lb 15,500 cP Nil PlatSil® HTS-25 FAST 1A:10B A25 15 min. 3 hr. Milky White 24.9 in³/lb 18,000 cP Nil PlatSil® HTS-40 1A:10B A40 30 min. 24 hr. Milky White 24.9 in³/lb 17,000 cP Nil PlatSil® Gel-OO20 1A:1B OO20 40 min. 2 hr. Milky White 26 in³/lb 3,900 cP Nil PlatSil® Gel-OO30 1A:1B 0030 45 min. 4 hr. Milky White 26 in³/lb 6,200 cP Nil PlatSil® Gel-OO 1A:1B 0030 6 min. 30 min. Milky White 25 in³/lb 22,000 cP Nil PlatSil® Gel-10 1A:1B A10 6 min. 30 min. Milky White 25 in³/lb 15,000 cP Nil PlatSil® Gel-25 1A:1B A25 5 min. 60 min. Milky White 25 in³/lb 3,500 cP Nil   PlatSil® 71-11 Silicone Rubber is a two-part, platinum-catalyzed, liquid silicone system that cures (RTV) to a blue-green, Shore A10 rubber. This is a pourable rubber, but it can be easily thickened with PlatThix Liquid Thickener or Fumed Silica for brush-on application. PlatSil® 73-15 Silicone Rubber is a two-part, platinum-catalyzed, liquid silicone system that cures (RTV) to a white translucent, Shore A15 rubber. The transparent nature of the cured rubber makes it a good option for molds that need to be cut after cured – because the model is visible, parting lines can be better determined. It is also very useful when casting intricate parts to ensure that the entire mold cavity has been filled with casting material. This is a pourable rubber, but it can be easily thickened with PlatThix Liquid Thickener or Fumed Silica for brush-on application. PlatSil® 73-20 Silicone Rubber is a two-part, platinum-catalyzed, liquid silicone system that cures (RTV) to a blue translucent, Shore A20 rubber. Compared to other silicones in the PlatSil® 73-Series line, this option sets quickly with a demold time of 1 hour (at room temperature). The transparency of PlatSil® 73-20 is useful for molds that need to be cut after cure – parting lines can be better determined because the model is visible. This is a pourable rubber, but it can be easily thickened with PlatThix Liquid Thickener or Fumed Silica for brush-on application. PlatSil® 71-25 Silicone Rubber is a two-part, platinum-catalyzed, liquid silicone system that cures (RTV) to a milky white, Shore A25 rubber. This is a pourable rubber, but it can be easily thickened with PlatThix Liquid Thickener or Fumed Silica for brush-on application.  PlatSil® 71-25 has been tested by an independent laboratory and was found to comply with 21 CFR 177.2600 (as published in the Code of Federal Regulations) for rubber articles intended for repeated use food contact surfaces when accurately measured, thoroughly mixed, and fully cured. Review our Food-Related Applications Technical Bulletin. PlatSil® 73-25 Silicone Rubber is a two-part, platinum-catalyzed, liquid silicone system that cures (RTV) to a green, Shore A25 rubber. This is a pourable rubber, but it can be easily thickened with PlatThix Liquid Thickener or Fumed Silica for brush-on application. The yellow colored Part A and green colored Part B make it easy to see when mixing is complete. A uniform, light, lime-green color means you’re good to go! PlatSil® 73-29 Silicone Rubber is a two-part, platinum-catalyzed, liquid silicone system that cures (RTV) to a white, Shore A30 rubber. This is a pourable rubber, but it can be easily thickened with PlatThix Liquid Thickener or Fumed Silica for brush-on application. PlatSil® 71-40 Silicone Rubber is a two-part, platinum-catalyzed, liquid silicone system that cures (RTV) to a translucent, Shore A40 rubber. This is a pourable rubber, but it can be easily thickened with PlatThix Liquid Thickener or Fumed Silica for brush-on application. PlatSil® 73-40 Silicone Rubber is a two-part, platinum-catalyzed, liquid silicone system that cures (RTV) to a yellow, Shore A40 rubber. Since PlatSil® 73-40 has no shrinkage upon curing and resists mold distortion due to casting, it is an ideal product where dimensional stability is required. This is a pourable rubber, but it can be easily thickened with PlatThix Liquid Thickener or Fumed Silica for brush-on application. PlatSil® 73-45 Silicone Rubber is a two-part, platinum-catalyzed, liquid silicone system that cures (RTV) to a green, Shore A45 rubber. This is a pourable rubber, but it can be easily thickened with PlatThix Liquid Thickener or Fumed Silica for brush-on application.  PlatSil® 73-45 has been tested by an independent laboratory and w

Mold making silicone rubber products that make it easy to create flexible molds for casting jewelry, sculptures, props, and more.

Food Grade Silicone Rubber for Mold MakingCast-A-Mold Platinum is a versatile food grade platinum (addition) cured silicone rubber designed for a wide variety of mold making applications. It offers exceptional performance with its 1:1 mix ratio (by weight), low viscosity, excellent tear strength, tensile strength, elongation, heat deflection, and long silicone mold library life.Custom Mold Applications:The project possibilities for Cast-a-Mold Platinum go far beyond crafting custom resin molds. It can be used to make translucent silicone molds for variety of projects, such as:Casting candies and chocolatesCake decoratingCasting polyurethanesEpoxy resin castingPolyester resin castingCementConcreteSoap makingCandle making (and other wax applications)Plasterand many more!Cast-A-Mold Platinum molding silicone is user friendly and FDA compliant, ensuring safe use in food-related applications. Another advantage is its ability to cure at room temperature, eliminating the need for specialized equipment or vacuum chambers.Cast-A-Mold Platinum Notes and Tips:Platinum cured silicone rubber can be heat accelerated. For instance, if you expose the mold to a temperature of 150°F (65°C), the curing time will be significantly reduced from 8 hours to just 30 minutes.It's important to note that for food applications, it is recommended to wash the cured mold with warm water and soap before using it to ensure cleanliness and hygienic standards.Addition-cure silicone rubber may be affected by certain contaminants, which can lead to tackiness on the surface of the mold. To avoid this, it's best to steer clear of materials like latex, sulfur-based clays, tin cured silicone rubber, amines, nitriles, and organo-metallic salt-containing compounds. If you're uncertain about the compatibility of the substrate being molded, it's always a good practice to conduct a small compatibility test beforehand. Additionally, applying a clear acrylic lacquer or paint on the pattern can help prevent inhibition. However, polyurethane and latex should not be used in this context.Cast-A-Mold Platinum is comparable to Smooth-on Mold Star™, Smooth-Sil™, SORTA-Clear™, Ecoflex™ and Dragon Skin™ silicones.

If you purchased this toy and would like to add a second or more additional color to this toy, please visit our store for additional color items: https://www.etsy.com/listing/1308729700/extra-colors-for-toys-add-color-to-item All of our toys are poured with 100% platinum cure silicone. This type of silicone is the highest grade material and is odorless and non-toxic for medical use. Platinum silicone is also non-porous, hypoallergenic and easy to clean. 100% Discreet Shipping Approximate Measurements: Small: Diameter: 1.5” / 3.8 cm, height(Highest): 0.8” / 2 cm, Weight: 19 g / 0.7 oz Medium: Diameter: 2” / 5.2 cm, height(Highest): 1.1” / 2.9 cm, Weight: 46 g / 1.6 oz Large: Diameter: 2.8” / 7.2 cm, height(Highest): 1.7” / 4.2 cm, Weight: 122 g / 4.3 oz Firmness: Medium Super Soft Shore 00-20 Rating With this tool, you can temporarily attach each toy with a flat base to any smooth surface. Add a little water before, press it, and it's ready to use! Check out our store - Plutoying.etsy.com Please note： 1.Because it is handmade, the product will not be exactly the same as the picture, but it is basically the same. 2. we are not responsible for any issues that arise from an order being purchased with the wrong shipping address. 3 Due to the brightness of the monitor and light brightness, the real color maybe a little different from the pictures shown on the product page. Hope you understand. Logistics query URL: https://www.17track.net/en

Extraordinarily soft, strong and durable platinum cure silicones

Silicone Rubber - Polytek Platsil - Liquid Silicone Platinum Cured Polytek® manufactures a full range of two-part, room-temperature curing silicone rubbers that offer great flexibility, tear strength, chemical resistance, and release properties. Silicone molds can be used to cast a variety of materials, including polyurethane, polyester and epoxy resins, polyurethane foam, plaster, wax, concrete, low melting metals, and more. One of the primary advantages of using silicone mold rubbers instead of other flexible materials, like polyurethane rubber, is that release agent is not needed when casting polyurethane resins, foams and other materials into silicone molds. This is especially important when cast parts need to be painted as paint will not adhere well to parts with residual release agent. **We often get asked how much is in a kit, and the answer is below under each product's 'Specific Volume'-- But, to simplify, if 1lb of material has a volume of 25 cubic inches, that is just under the size of a 3" x 3" x 3" cube, which is 27 cubic inches (picture a Rubik's Cube) Polytek® manufactures two different types of silicone rubbers: platinum-cured (PlatSil®) silicones and tin-cured (TinSil®) silicones:  There are distinct qualities that each line offers and their primary differences are:  TinSil® silicones are condensation-cure systems that shrink slightly on cure (~1%) compared to addition-cure PlatSil® silicones, which do not shrink on cure.  Cured TinSil® silicones have shorter library life (2 to 5 years total) compared to PlatSil® silicones. TinSil® silicones are slightly less expensive than PlatSil® silicones.  Liquid PlatSil® silicones are more sensitive to certain materials (e.g., sulfur, tin compounds, Bondo) and suffer from cure inhibition (uncured surface material) more often than TinSil® silicones. Cured TinSil® molds can inhibit some casting materials, including PlatSil® silicones, Poly-Optic® Clear Casting Resin and many polyurethane rubbers. There are skin-safe platinum-cured silicones available in the PlatSil® product line: PlatSil® Gels.      PlatSil (Plastinum Care) Silicone Rubber: Use PlatSil® Liquid Silicone Rubbers to make your own silicone molds and silicone parts. PlatSil® rubbers are platinum-cured (also known as addition-cure), room temperature-curing silicones (RTV) that are used to make flexible, high-strength molds and parts. PlatSil® molds are often selected over other mold materials (e.g., polyurethane rubbers) because of their excellent release properties. They also exhibit long library life and low shrinkage on cure compared to other mold material options. PlatSil® molds are excellent for casting polyurethane, epoxy and polyester resin, polyurethane foam, wax, plaster, soap, concrete, and more. Release agent is generally not needed to cast any of these materials. These rubbers are commonly used in Sculpture & Foundry, Prototyping, Architectural Reproduction & Restoration, Foam, Plastic & Plaster Millwork & Ornamentation, Theming & Display, Candle Making, Craft & Hobby projects, and some Concrete Casting applications. PlatSil Features: Two-part platinum-cured (addition-cure) silicone rubbers Room temperature curing (RTV) Shore Hardness Options: A10-A60 Do not exhibit shrinkage upon curing so they are useful for casting dimensionally stable parts for highly accurate prototyping and model making applications Molds do not require release agents when casting most materials Cured molds have a long library life Pourable or brushable (thicken with PlatThix liquid thickener or Fumed Silica) High-strength Excellent chemical resistance Reproduces fine details Can be accelerated for rapid cure Ideal for the most demanding resin casting applications NOTE ON CURE INHIBITION: Sulfur/tin/amine-contaminated materials and tools will cause cure inhibition in platinum-cured silicone rubbers, which means that the rubber that is in contact with the contaminated surface will remain gummy or uncured. Make sure to test cure the rubber on your surface before full-scale application. Use a polyurethane or tin-cured silicone rubber if you know that you’ll be working with any of these inhibitors. PlatSil® 71 & 73-Series Silicone Rubbers Listed below in order of hardness (softest at top).  Standard, platinum-cured mold making and casting silicone rubbers. PlatSil® 71 & 73-Series Technical Bulletin (TDS) PlatSil® FS-Series Technical Bulletin (TDS) PlatSil® Gel Series Technical Bulletin (TDS) PlatSil® Safety Data Sheet (SDS) PlatSil® FS-Series Safety Data Sheet (SDS) Product Mix Ratio by Weight Shore Hardness Pour Time Demold Time Cured Color Specific Volume Mixed Viscosity Shrinkage Upon Cure PlatSil® 71-11 1A:1B A10 20 min. 4 hr. Blue-Green 24.7 in³/lb 6,000 cP Nil PlatSil® 73-15 1A:1B A15 20 min. 4-5 hr. White Translucent 25.0 in³/lb 2,500 cP Nil PlatSil® 73-20 1A:1B A22 5 min. 1 hr. Blue Translucent 25.0 in³/lb 3,000 cP Nil PlatSil® 71-25 1A:1B A25 35 min. 16 hr. Milky White 25.0 in³/lb 3,500 cP Nil PlatSil® 73-25 1A:1B A25 15 min. 4-5 hr. Green 24.3 in³/lb 6,000 cP Nil PlatSil® 73-29 1A:10B A30 45 min. 16 hr. White 25.0 in³/lb 15,000 cP Nil PlatSil® 71-40 1A:10B A40 90 min. 24 hr. Translucent 26.6 in³/lb 38,000 cP Nil PlatSil® 73-40 1A:10B A40 45 min. 16 hr. Yellow 22.0 in³/lb 25,000 cP Nil PlatSil® 73-45 1A:10B A45 40 min. 16 hr. Green 21.3 in³/lb 35.000 cP Nil PlatSil® 73-60 1A:10B A60 45 min. 16 hr. Blue 21.3 in³/lb 40,000 cP Nil PlatSil® FS-10 1A:1B OO60/A13 8 min. 25 min. Milky White 24.9 in³/lb 4,200 cP Nil PlatSil® FS-20 1A:1B OO66/A20 8 min. 25 min. Milky White 24.9 in³/lb 3,800 cP Nil PlatSil® HTS-25 1A:10B A25 70 min. 24 hr. Milky White 24.9 in³/lb 15,500 cP Nil PlatSil® HTS-25 FAST 1A:10B A25 15 min. 3 hr. Milky White 24.9 in³/lb 18,000 cP Nil PlatSil® HTS-40 1A:10B A40 30 min. 24 hr. Milky White 24.9 in³/lb 17,000 cP Nil PlatSil® Gel-OO20 1A:1B OO20 40 min. 2 hr. Milky White 26 in³/lb 3,900 cP Nil PlatSil® Gel-OO30 1A:1B 0030 45 min. 4 hr. Milky White 26 in³/lb 6,200 cP Nil PlatSil® Gel-OO 1A:1B 0030 6 min. 30 min. Milky White 25 in³/lb 22,000 cP Nil PlatSil® Gel-10 1A:1B A10 6 min. 30 min. Milky White 25 in³/lb 15,000 cP Nil PlatSil® Gel-25 1A:1B A25 5 min. 60 min. Milky White 25 in³/lb 3,500 cP Nil   PlatSil® 71-11 Silicone Rubber is a two-part, platinum-catalyzed, liquid silicone system that cures (RTV) to a blue-green, Shore A10 rubber. This is a pourable rubber, but it can be easily thickened with PlatThix Liquid Thickener or Fumed Silica for brush-on application. PlatSil® 73-15 Silicone Rubber is a two-part, platinum-catalyzed, liquid silicone system that cures (RTV) to a white translucent, Shore A15 rubber. The transparent nature of the cured rubber makes it a good option for molds that need to be cut after cured – because the model is visible, parting lines can be better determined. It is also very useful when casting intricate parts to ensure that the entire mold cavity has been filled with casting material. This is a pourable rubber, but it can be easily thickened with PlatThix Liquid Thickener or Fumed Silica for brush-on application. PlatSil® 73-20 Silicone Rubber is a two-part, platinum-catalyzed, liquid silicone system that cures (RTV) to a blue translucent, Shore A20 rubber. Compared to other silicones in the PlatSil® 73-Series line, this option sets quickly with a demold time of 1 hour (at room temperature). The transparency of PlatSil® 73-20 is useful for molds that need to be cut after cure – parting lines can be better determined because the model is visible. This is a pourable rubber, but it can be easily thickened with PlatThix Liquid Thickener or Fumed Silica for brush-on application. PlatSil® 71-25 Silicone Rubber is a two-part, platinum-catalyzed, liquid silicone system that cures (RTV) to a milky white, Shore A25 rubber. This is a pourable rubber, but it can be easily thickened with PlatThix Liquid Thickener or Fumed Silica for brush-on application.  PlatSil® 71-25 has been tested by an independent laboratory and was found to comply with 21 CFR 177.2600 (as published in the Code of Federal Regulations) for rubber articles intended for repeated use food contact surfaces when accurately measured, thoroughly mixed, and fully cured. Review our Food-Related Applications Technical Bulletin. PlatSil® 73-25 Silicone Rubber is a two-part, platinum-catalyzed, liquid silicone system that cures (RTV) to a green, Shore A25 rubber. This is a pourable rubber, but it can be easily thickened with PlatThix Liquid Thickener or Fumed Silica for brush-on application. The yellow colored Part A and green colored Part B make it easy to see when mixing is complete. A uniform, light, lime-green color means you’re good to go! PlatSil® 73-29 Silicone Rubber is a two-part, platinum-catalyzed, liquid silicone system that cures (RTV) to a white, Shore A30 rubber. This is a pourable rubber, but it can be easily thickened with PlatThix Liquid Thickener or Fumed Silica for brush-on application. PlatSil® 71-40 Silicone Rubber is a two-part, platinum-catalyzed, liquid silicone system that cures (RTV) to a translucent, Shore A40 rubber. This is a pourable rubber, but it can be easily thickened with PlatThix Liquid Thickener or Fumed Silica for brush-on application. PlatSil® 73-40 Silicone Rubber is a two-part, platinum-catalyzed, liquid silicone system that cures (RTV) to a yellow, Shore A40 rubber. Since PlatSil® 73-40 has no shrinkage upon curing and resists mold distortion due to casting, it is an ideal product where dimensional stability is required. This is a pourable rubber, but it can be easily thickened with PlatThix Liquid Thickener or Fumed Silica for brush-on application. PlatSil® 73-45 Silicone Rubber is a two-part, platinum-catalyzed, liquid silicone system that cures (RTV) to a green, Shore A45 rubber. This is a pourable rubber, but it can be easily thickened with PlatThix Liquid Thickener or Fumed Silica for brush-on application.  PlatSil® 73-45 has been tested by an independent laboratory and w

1 lbs total part A and B Smooth-On Psycho Paint is a versatile and easy to use platinum silicone paint base developed to help special effects and prosthetic artisans, doll makers, etc. easily create painted-on color effects for their platinum silicone creations. It is a two component translucent clear platinum-cure silicone that is used to make a base for color pigmenting. Once the desired color is attained, Psycho Paint is thinned with a solvent such as naptha (you can buy it from a paint store) or toluene. Doesnt have to be thinned. Thin layers of paint CAN be then be applied to a model's surface (made of Dragon Skin, Ecoflex or other platinum silicone) using an airbrush! In addition to painting the exterior of a cast piece, you can apply Psycho Paint to the inside of a platinum silicone or urethane rubber mold and then cast platinum silicone behind it. It can also be applied by brushing

Interior Size: 12.0x3.7x1.25" Fluid Volume: 6oz / 177ml Wall Thickness: 1/2" Material: Platinum Cure Silicone - Shore 30A Interior Finish: Polished / Shiny Create beautiful solid resin or chocolate/candy roses complete with stems and leaves. Flat backed to allow for wall mounting or to cast within additional large resin art pieces. Total depth of the rose is approximately 1.25" the stem body and leaf is ~5/8". Note that the mold is contiguous and has no separation between elements, so "painting with pigment" in advance of pouring resin, or creating temporary dams to prevent color leaking will be required if you wish to create a multicolored piece. Painting or coating after casting is also a possibility.  Like our other RSCC molds it can also be used for chocolate, baking and candy making. The sky is the limit!

Introducing Pebbles the Frog! A stress ball stim toy in the palm of your hand! They're ultra squishy, perfect for squeezing, poking and prodding to reduce stress! Need to focus? Pebbles is the perfect fidget! Pebbles is made from non-toxic skin-safe platinum-cure silicone to ensure the highest quality fidget toys for our customers! Pebbles comes in two sizes, Small and Large, in six different curated colors. Not sure what color to choose? Select Random Color for a discounted price! Random colors may include limited edition and unlisted specialty colors, in addition to standard choices -- you never know what you're gonna get!

Use this silicon mold to create a candle vessel or a planter using wide variety of casting materials. The package includes both the silicone mold and mold support to ensure perfect shape of the product every time. Silicon mold for lid sold separately. * Durable and long-lasting platinum-cured silicone that is suitable for concrete, plaster, resin or other casting materials. * Easy to demold, stretchy, and yet able to hold shape even without the casting frame. * The jar holds 32 fluid ounces of wax, with additional space for a wick. It is recommended to use 3-4 wicks depending on size. * Perfect for DIY enthusiasts or business owners * Designed and handcrafted in Arizona, USA. volume 32 fluid oz, diameter 6.25inches, height 3inches, wall thickness 8mm

Silicone Rubber - Polytek Platsil - Liquid Silicone Platinum Cured Polytek® manufactures a full range of two-part, room-temperature curing silicone rubbers that offer great flexibility, tear strength, chemical resistance, and release properties. Silicone molds can be used to cast a variety of materials, including polyurethane, polyester and epoxy resins, polyurethane foam, plaster, wax, concrete, low melting metals, and more. One of the primary advantages of using silicone mold rubbers instead of other flexible materials, like polyurethane rubber, is that release agent is not needed when casting polyurethane resins, foams and other materials into silicone molds. This is especially important when cast parts need to be painted as paint will not adhere well to parts with residual release agent. **We often get asked how much is in a kit, and the answer is below under each product's 'Specific Volume'-- But, to simplify, if 1lb of material has a volume of 25 cubic inches, that is just under the size of a 3" x 3" x 3" cube, which is 27 cubic inches (picture a Rubik's Cube) Polytek® manufactures two different types of silicone rubbers: platinum-cured (PlatSil®) silicones and tin-cured (TinSil®) silicones:  There are distinct qualities that each line offers and their primary differences are:  TinSil® silicones are condensation-cure systems that shrink slightly on cure (~1%) compared to addition-cure PlatSil® silicones, which do not shrink on cure.  Cured TinSil® silicones have shorter library life (2 to 5 years total) compared to PlatSil® silicones. TinSil® silicones are slightly less expensive than PlatSil® silicones.  Liquid PlatSil® silicones are more sensitive to certain materials (e.g., sulfur, tin compounds, Bondo) and suffer from cure inhibition (uncured surface material) more often than TinSil® silicones. Cured TinSil® molds can inhibit some casting materials, including PlatSil® silicones, Poly-Optic® Clear Casting Resin and many polyurethane rubbers. There are skin-safe platinum-cured silicones available in the PlatSil® product line: PlatSil® Gels.      PlatSil (Plastinum Care) Silicone Rubber: Use PlatSil® Liquid Silicone Rubbers to make your own silicone molds and silicone parts. PlatSil® rubbers are platinum-cured (also known as addition-cure), room temperature-curing silicones (RTV) that are used to make flexible, high-strength molds and parts. PlatSil® molds are often selected over other mold materials (e.g., polyurethane rubbers) because of their excellent release properties. They also exhibit long library life and low shrinkage on cure compared to other mold material options. PlatSil® molds are excellent for casting polyurethane, epoxy and polyester resin, polyurethane foam, wax, plaster, soap, concrete, and more. Release agent is generally not needed to cast any of these materials. These rubbers are commonly used in Sculpture & Foundry, Prototyping, Architectural Reproduction & Restoration, Foam, Plastic & Plaster Millwork & Ornamentation, Theming & Display, Candle Making, Craft & Hobby projects, and some Concrete Casting applications. PlatSil Features: Two-part platinum-cured (addition-cure) silicone rubbers Room temperature curing (RTV) Shore Hardness Options: A10-A60 Do not exhibit shrinkage upon curing so they are useful for casting dimensionally stable parts for highly accurate prototyping and model making applications Molds do not require release agents when casting most materials Cured molds have a long library life Pourable or brushable (thicken with PlatThix liquid thickener or Fumed Silica) High-strength Excellent chemical resistance Reproduces fine details Can be accelerated for rapid cure Ideal for the most demanding resin casting applications NOTE ON CURE INHIBITION: Sulfur/tin/amine-contaminated materials and tools will cause cure inhibition in platinum-cured silicone rubbers, which means that the rubber that is in contact with the contaminated surface will remain gummy or uncured. Make sure to test cure the rubber on your surface before full-scale application. Use a polyurethane or tin-cured silicone rubber if you know that you’ll be working with any of these inhibitors. PlatSil® 71 & 73-Series Silicone Rubbers Listed below in order of hardness (softest at top).  Standard, platinum-cured mold making and casting silicone rubbers. PlatSil® 71 & 73-Series Technical Bulletin (TDS) PlatSil® FS-Series Technical Bulletin (TDS) PlatSil® Gel Series Technical Bulletin (TDS) PlatSil® Safety Data Sheet (SDS) PlatSil® FS-Series Safety Data Sheet (SDS) Product Mix Ratio by Weight Shore Hardness Pour Time Demold Time Cured Color Specific Volume Mixed Viscosity Shrinkage Upon Cure PlatSil® 71-11 1A:1B A10 20 min. 4 hr. Blue-Green 24.7 in³/lb 6,000 cP Nil PlatSil® 73-15 1A:1B A15 20 min. 4-5 hr. White Translucent 25.0 in³/lb 2,500 cP Nil PlatSil® 73-20 1A:1B A22 5 min. 1 hr. Blue Translucent 25.0 in³/lb 3,000 cP Nil PlatSil® 71-25 1A:1B A25 35 min. 16 hr. Milky White 25.0 in³/lb 3,500 cP Nil PlatSil® 73-25 1A:1B A25 15 min. 4-5 hr. Green 24.3 in³/lb 6,000 cP Nil PlatSil® 73-29 1A:10B A30 45 min. 16 hr. White 25.0 in³/lb 15,000 cP Nil PlatSil® 71-40 1A:10B A40 90 min. 24 hr. Translucent 26.6 in³/lb 38,000 cP Nil PlatSil® 73-40 1A:10B A40 45 min. 16 hr. Yellow 22.0 in³/lb 25,000 cP Nil PlatSil® 73-45 1A:10B A45 40 min. 16 hr. Green 21.3 in³/lb 35.000 cP Nil PlatSil® 73-60 1A:10B A60 45 min. 16 hr. Blue 21.3 in³/lb 40,000 cP Nil PlatSil® FS-10 1A:1B OO60/A13 8 min. 25 min. Milky White 24.9 in³/lb 4,200 cP Nil PlatSil® FS-20 1A:1B OO66/A20 8 min. 25 min. Milky White 24.9 in³/lb 3,800 cP Nil PlatSil® HTS-25 1A:10B A25 70 min. 24 hr. Milky White 24.9 in³/lb 15,500 cP Nil PlatSil® HTS-25 FAST 1A:10B A25 15 min. 3 hr. Milky White 24.9 in³/lb 18,000 cP Nil PlatSil® HTS-40 1A:10B A40 30 min. 24 hr. Milky White 24.9 in³/lb 17,000 cP Nil PlatSil® Gel-OO20 1A:1B OO20 40 min. 2 hr. Milky White 26 in³/lb 3,900 cP Nil PlatSil® Gel-OO30 1A:1B 0030 45 min. 4 hr. Milky White 26 in³/lb 6,200 cP Nil PlatSil® Gel-OO 1A:1B 0030 6 min. 30 min. Milky White 25 in³/lb 22,000 cP Nil PlatSil® Gel-10 1A:1B A10 6 min. 30 min. Milky White 25 in³/lb 15,000 cP Nil PlatSil® Gel-25 1A:1B A25 5 min. 60 min. Milky White 25 in³/lb 3,500 cP Nil   PlatSil® 71-11 Silicone Rubber is a two-part, platinum-catalyzed, liquid silicone system that cures (RTV) to a blue-green, Shore A10 rubber. This is a pourable rubber, but it can be easily thickened with PlatThix Liquid Thickener or Fumed Silica for brush-on application. PlatSil® 73-15 Silicone Rubber is a two-part, platinum-catalyzed, liquid silicone system that cures (RTV) to a white translucent, Shore A15 rubber. The transparent nature of the cured rubber makes it a good option for molds that need to be cut after cured – because the model is visible, parting lines can be better determined. It is also very useful when casting intricate parts to ensure that the entire mold cavity has been filled with casting material. This is a pourable rubber, but it can be easily thickened with PlatThix Liquid Thickener or Fumed Silica for brush-on application. PlatSil® 73-20 Silicone Rubber is a two-part, platinum-catalyzed, liquid silicone system that cures (RTV) to a blue translucent, Shore A20 rubber. Compared to other silicones in the PlatSil® 73-Series line, this option sets quickly with a demold time of 1 hour (at room temperature). The transparency of PlatSil® 73-20 is useful for molds that need to be cut after cure – parting lines can be better determined because the model is visible. This is a pourable rubber, but it can be easily thickened with PlatThix Liquid Thickener or Fumed Silica for brush-on application. PlatSil® 71-25 Silicone Rubber is a two-part, platinum-catalyzed, liquid silicone system that cures (RTV) to a milky white, Shore A25 rubber. This is a pourable rubber, but it can be easily thickened with PlatThix Liquid Thickener or Fumed Silica for brush-on application.  PlatSil® 71-25 has been tested by an independent laboratory and was found to comply with 21 CFR 177.2600 (as published in the Code of Federal Regulations) for rubber articles intended for repeated use food contact surfaces when accurately measured, thoroughly mixed, and fully cured. Review our Food-Related Applications Technical Bulletin. PlatSil® 73-25 Silicone Rubber is a two-part, platinum-catalyzed, liquid silicone system that cures (RTV) to a green, Shore A25 rubber. This is a pourable rubber, but it can be easily thickened with PlatThix Liquid Thickener or Fumed Silica for brush-on application. The yellow colored Part A and green colored Part B make it easy to see when mixing is complete. A uniform, light, lime-green color means you’re good to go! PlatSil® 73-29 Silicone Rubber is a two-part, platinum-catalyzed, liquid silicone system that cures (RTV) to a white, Shore A30 rubber. This is a pourable rubber, but it can be easily thickened with PlatThix Liquid Thickener or Fumed Silica for brush-on application. PlatSil® 71-40 Silicone Rubber is a two-part, platinum-catalyzed, liquid silicone system that cures (RTV) to a translucent, Shore A40 rubber. This is a pourable rubber, but it can be easily thickened with PlatThix Liquid Thickener or Fumed Silica for brush-on application. PlatSil® 73-40 Silicone Rubber is a two-part, platinum-catalyzed, liquid silicone system that cures (RTV) to a yellow, Shore A40 rubber. Since PlatSil® 73-40 has no shrinkage upon curing and resists mold distortion due to casting, it is an ideal product where dimensional stability is required. This is a pourable rubber, but it can be easily thickened with PlatThix Liquid Thickener or Fumed Silica for brush-on application. PlatSil® 73-45 Silicone Rubber is a two-part, platinum-catalyzed, liquid silicone system that cures (RTV) to a green, Shore A45 rubber. This is a pourable rubber, but it can be easily thickened with PlatThix Liquid Thickener or Fumed Silica for brush-on application.  PlatSil® 73-45 has been tested by an independent laboratory and w

Exclusive to Myka Candles & Moulds and hand-poured to order in Australia using premium platinum-cure silicone. Please allow up to 5 business days to process. Introducing the Sakura Vessel – a versatile piece that serves as both a candle holder and a trinket dish. Its elegant shape and delicate cherry blossom debossed design make it a charming addition to any space. Once the candle has burned down, the vessel can be repurposed to store your cherished items, combining beauty and functionality seamlessly. Our custom Sakura Vessel is true work of art meticulously designed that is 3D printed and handpoured within our studio. You won't find this exquisite mould anywhere else, as each one is created to order by us using the highest-grade platinum-cure silicone. Precision and passion come together in the crafting of this handmade vessel mould, opening the door to boundless creative possibilities. This mould is compatible with various materials, including concrete, hydrostone, jesmonite, plaster, resin, and more. To make the most of your vessel mould, follow these steps: • Preparation: Begin by gathering your selected material and ensure it's mixed according to the manufacturer's instructions. • Pouring: Carefully fill the mould with your chosen material, ensuring it reaches the top. • Air Bubble Removal: For a smoother finish, gently tap the mould on a sturdy surface to encourage any trapped air bubbles to rise to the surface. • Curing: Adhere to the recommended curing time for your chosen material. • Demoulding: Once the material has set and cured, carefully flex and remove the mould to unveil your creation. Before making a candle in your vessel, it is vital to seal it with a heat-resistant sealer. Apply at least two coats to both the interior and exterior of the vessel. Ensure the sealant is fully dry before pouring in the wax. We recommend using 3-5 wicks for an even burn. Keep in mind that the vessel's diameter varies from top to middle to bottom, so you may need different-sized wicks to ensure an efficient and even burn. With our Christmas Tree Candle Vessel Mould, you're not only creating artistry but also enhancing the festive spirit with your personalized candle creations. Get ready to illuminate the holiday season with your unique touch! Specifications Finished product:  External - 5cm (H) x 16.5cm (W) x 16.5.  cm (L) Internal - 4cm (H) x 14.5cm (W) x 11.5cm (L) Wax volume:  Wick recommendation: Mould Care Always store silicone moulds in their original shape and never leave them turned inside out. Keeping the mould in its intended form prevents the silicone from tearing due to prolonged exposure to unnatural positions. Clean with warm water and mild soap after every use and store in a dust-free environment. Disclaimer: mould is poured and trimmed by hand and therefore may have some minor exterior imperfections.

Food Grade Silicone Rubber for Mold MakingCast-A-Mold Platinum is a versatile food grade platinum (addition) cured silicone rubber designed for a wide variety of mold making applications. It offers exceptional performance with its 1:1 mix ratio (by weight), low viscosity, excellent tear strength, tensile strength, elongation, heat deflection, and long silicone mold library life.Custom Mold Applications:The project possibilities for Cast-a-Mold Platinum go far beyond crafting custom resin molds. It can be used to make translucent silicone molds for variety of projects, such as:Casting candies and chocolatesCake decoratingCasting polyurethanesEpoxy resin castingPolyester resin castingCementConcreteSoap makingCandle making (and other wax applications)Plasterand many more!Cast-A-Mold Platinum molding silicone is user friendly and FDA compliant, ensuring safe use in food-related applications. Another advantage is its ability to cure at room temperature, eliminating the need for specialized equipment or vacuum chambers.Cast-A-Mold Platinum Notes and Tips:Platinum cured silicone rubber can be heat accelerated. For instance, if you expose the mold to a temperature of 150°F (65°C), the curing time will be significantly reduced from 8 hours to just 30 minutes.It's important to note that for food applications, it is recommended to wash the cured mold with warm water and soap before using it to ensure cleanliness and hygienic standards.Addition-cure silicone rubber may be affected by certain contaminants, which can lead to tackiness on the surface of the mold. To avoid this, it's best to steer clear of materials like latex, sulfur-based clays, tin cured silicone rubber, amines, nitriles, and organo-metallic salt-containing compounds. If you're uncertain about the compatibility of the substrate being molded, it's always a good practice to conduct a small compatibility test beforehand. Additionally, applying a clear acrylic lacquer or paint on the pattern can help prevent inhibition. However, polyurethane and latex should not be used in this context.Cast-A-Mold Platinum is comparable to Smooth-on Mold Star™, Smooth-Sil™, SORTA-Clear™, Ecoflex™ and Dragon Skin™ silicones.

Introducing Shelby the Shark! A stress ball stim toy in the palm of your hand! They're ultra squishy, perfect for squeezing, poking and prodding to reduce stress! Need to focus? Shelby is the perfect fidget! Shelby is made from non-toxic skin-safe platinum-cure silicone to ensure the highest quality fidget toys for our customers! Shelby comes in two sizes, Small and Large, in six different curated colors. Not sure what color to choose? Select Random Color for a discounted price! Random colors may include limited edition and unlisted specialty colors, in addition to standard choices -- you never know what you're gonna get!

Polytek PolyCoat Sealer/Release for Rubber Mold Making PolyCoat Sealer & Release Agent is a low-viscosity, semi-permanent sealer and release agent that leaves behind a thin coating of silicone. FOR INDUSTRIAL/PROFESSIONAL USE ONLY.  For Mold Making: Apply PolyCoat to porous (may require multiple coats depending on porosity) or non-porous models when making polyurethane and platinum-cured silicone rubber molds (not recommended for use with liquid tin-cured silicone rubber). Since PolyCoat leaves a dry, cured silicone coating on a surface, it may be used without additional release agent. This can be quite advantageous when making a polyurethane rubber mold as no residual release will transfer to the cured mold surface from the mold making process. For Casting: PolyCoat can also be applied to aging PlatSil® and TinSil® Silicone Molds to improve performance (easier demolding) and extend their useful life. In addition, PolyCoat can be applied to firm polyurethane rubber molds to give them a thin silicone skin on the mold face. This can allow materials such as polyurethane plastics or foams, that would ordinarily require releases, to be cast into dry polyurethane molds at a reduced cost. NOTES: Cure time varies between 30 minutes and 16 hours depending on temperature, humidity and porosity of the model; ensure that PolyCoat has completely cured before applying liquid rubber or plastic. Very porous surfaces may require multiple coats of PolyCoat, applied ~15-20 minutes apart. Care should be taken to adequately seal the surface, but not over-apply; as with other sealers, surface details on the model can be lost when a sealer is over-applied. When brushing, be careful not to leave brush marks on the surface as the PolyCoat begins to gel. One common technique used when either brushing or spraying is to apply the PolyCoat then flip the master over to allow excess to run off. This leaves a thin coating behind and helps to eliminate brush marks or surface defects. Do not use PolyCoat to seal plaster. Gypsum models tend to aggressively wick the solvent into pores and the curing process can be slow or incomplete, leaving some residual solvent behind, which may interfere with the cure of certain rubbers. PolyCoat is one-part moisture-curable silicone sealant which can be sprayed or brushed to seal porous models before applying liquid rubber. In many cases, PolyCoat serves as both the sealer and release eliminating the need for further release application when using liquid polyurethane mold rubbers. PolyCoat can be applied to rigid masters as well as to cured rubber molds to provide semi-permanent release and mold longevity. PolyCoat should be used to seal a surface such as wood, tile, stone, concrete, plaster, etc. before creating a rubber mold. PolyCoat can also be used to create a semi-permanent 'release' on a master polyurethane mold that will have repeated molds made from it, and won't need Pol-Ease 2300 Release applied each time. Polyurethane Rubber molds treated with PolyCoat imitate Silicone Rubber molds. Do Not use pour liquid Silicone Rubber on surfaces treated with PolyCoat. Sold in Quart (1.5 lbs), and Gallon (8 lbs) sizes. Documentation: PolyCoat SDS Sheet Sealer/Release Mold Making Product Guide Application Information: Brush or spray 1 to 3 thin coats of PolyCoat on surface. Allow to dry 10 minutes between coats. Let final coat dry 30 minutes in warm area or under heat lamp.