- - For 4x4 (3.5" x3.5") Posts - - For 4x4 (3.5" x3.5") Posts- - For 4x4 (3.5" x3.5") Posts This listing is for our Outside Corners and other individually sold brackets made to fit 4 x 4 Posts and Beams. If you want them for 6 x 6 posts, click here: https://www.etsy.com/listing/708942856 (NOTE: All our brackets are based on the dimensional size of the lumber but we can make them actual 4"x4" or 6"x6" for you, if needed. Just let us know your ship-to zip code, the parts and actual size(s) you would like and we can let you know the total cost for custom brackets made to fit your saw-mill-cut posts.) Build your own rugged and heavy duty PostHugger™ Pergola, Double Pergola, shop/garage/CNC table, deck or even a wedding arch chuppah with our USA made 1/8" steel Outside Corner brackets and more! Also great for fixing/reinforcing the one you already have! These are not flimsy/bendable metal. We make them using 1/8" thick steel - a single corner bracket weighs just over 2 pounds - - strong enough to take what you throw at it (or what you throw it at!), but not so heavy where they are hard to work with. Our brackets can be installed using any 1/2" wood lag screws or in instances where there will not be a collision of bolt holes, 1/2" thru bolts. If you use lag screws, we recommend 1/2" x at least 2" length for 4x4 posts and at least 2.5" length for 6x6 posts, with longer bolts adding more strength. WOOD AND BOLTS/LAG SCREWS ARE NOT INCLUDED WITH OUR BRACKETS. Please note that unless you choose the powder coated option, these ship as raw, unpainted steel. You can either paint them the color of your choice, finish them with a clear coat, or allow to achieve a natural rust patina over time. ***Powder Coated Brackets: If ordering brackets in the black powder coat, please allow an additional 1-2 days for shipping & delivery.*** WHY BUY POSTHUGGER? • We are the original designer of these brackets, often copied by others but never equaled! • We use 1/8″ steel which is thicker than a Quarter and a Dime stacked on top of each other. • Unlike others who just cut and ship steel right off their table, we take the time to hand debur and wire brush both the inside and outside of every piece. • All powder coating is done in-house to ensure a quality application on each and every piece. • We use only 100% first-rate, high quality powders, which are all made in America. • We develop all designs ourselves and, unlike some, never poach the intellectual property of others. • We proudly stand behind all our products. • All our PostHugger™ Brackets & metal artwork products are Made in America with American-Made Steel! *************************** Our Brackets Product Line includes: Outside Corner Brackets - bent at a 90 degree angle to fit over any 4 x 4 post (3.5" x 3.5"). There are two 1/2" holes on each of the top ears for fastening to cross members and four 1/2" holes on the bottom leg for mounting to the legs. (The holes for the legs are offset so that if you want to thru bolt, you don't have to worry about hitting any of the other installed bolts!) Flat T brackets - join other parts of your design. Bent L’s - use where you want an inside corner. Flat L’s - Flat like the T, but without the third leg. Double Inside Corner - This is used on an inside corner to support two incoming posts. The holes are offset so that if used on the same post as an Outside Corner, they will not collide. Two Piece Post Base - Used to bolt a post to concrete or other suitable surface. If your post is going up against a wall or other flat surface which would interfere with having four feet, you will want to use either our Half-a-Post-Base, our 3-Sided Post Base (which has three feet) or our Full Post Base (which has just two feet) so that your post can be closer to a wall. Half a Post Base - This bracket is just one half of the Two Piece Post Base, for those who only need one (or another odd number). Three-Sided Post Base - Similar to our other Post Bases, but with three sides/feet. Full Post Base - Similar to our other Post Bases but with fours sides and just two feet (on opposite sides). Legless T™ - This bracket is the same dimensions & placement of bolt holes as the “T” - just without the bottom “leg” of the “T”! It measures 5.5" x 16.5" for a 6x6 post, and 3.5" x 10.25" for a 4x4 Post. Flat X™ Bracket - 90 degree cross angle brackets to provide extra, heavy duty support to new or existing DIY builds & structures. Flat Knee™ - This knee brace bracket sits flush against the outside of a knee joint. Bent Knee™ - This knee brace bracket is for use where you have a post coming in to meet another post at a 45° angle and want a bracket in the knee bend itself. *****EXTRA SHIPPING COST ON ALL BRACKET ORDERS TO NON-CONTIGUOUS UNITED STATES.***** Please call 470-626-5989 to place your order. If you would like to see customer photos (and a video!) of some of our brackets in use, copy and paste the following URL into your browser: https://posthugger.com/photos/ © 2024 Thermo-Flex Technologies, Inc. - All Designs, Photos, and Text are the Intellectual Property of Shop Owner and are not to be copied without express written permission.
This DIY pergola kit contains all the brackets and hardware you'll need to build your own pergola off back of house with roof (14 traditional roof rafters atop beams) and a privacy wall (8 slats). The attached-to-house pergola can be any size up to 24 feet wide (attached to house) by 24 feet deep (out from home) by 10 feet tall. The steel brackets for the pergola's frame are made for 6x6 wood posts (actual size: 5.5\" x 5.5\"), and the brackets for the traditional roof rafters and wall slats are made for 2x6 wood (actual size: 1.5\" x 5.5\"). The DIY-friendly kit includes stainless steel screws for securing the 6x6 and 2x6 wood into the steel brackets. Wood (lumber) not included.
Industrial Style Brackets for 6x6 Dimensional Lumber Beautiful, Strong, and Weatherproof, these brackets can add a decorative touch to any project. You won't get a better selection of color, variety or shapes of brackets than right here. Best of all We make custom brackets if you don't find exactly what you are looking for. If you need something quick just choose from our selection of brackets available or request a custom bracket by emailing us at [email protected]. We are here to help you make that exposed beam project look great. Sizes: X Bracket - 19 x 19 Inches T Bracket - 19 x 11.5 Inches L Bracket - 11.5 x 11.5 Inches Straight Bracket - 14 x 4 Inches Materials- Made of thick 12ga steel sourced from the USA. Painted with a super tough baked on powder coat finish with UV inhibitors that will not fade over time like most other paints. 11 color options available. Hole Sizes- Holes large enough for 1/4"-5/16" Bolts. (Hardware sold separately - Available Here) **Please note that you need to consult an Engineer if you want to know load calculations for your beams and ties.** All images and bracket designs are the sole property of Madison Iron and Wood and shall not be used by any other company, person, or entity without express permission.
Description Toja Grid freestanding 10-ft x 18-ft double pergola kit with 2 shade sails for 6x6 wood posts. No more complicated instructions and long set up times. Fast and easy assembly, roughly 60 minutes per section, with no special tools required. Lumber not included You can use any dry, straight lumber that fits our brackets and is strong enough to build a pergola. By design, our products allow you the freedom to choose your preferred wood to suit your build and budget. Note our brackets are made to fit dressed lumber. 4x4 wood is in fact 3.5”x3.5” - the industry simply calls it 4x4. 6x6 wood is in fact 5.5"x5.5" - the industry simply calls it 6x6. All of our brackets require only 2 screws per side (every set of eight holes). We leave the other holes open for future accessories
This DIY pergola kit contains all the brackets and hardware you'll need to build your own wooden outdoor pergola with roof (32 inline roof rafters) and one privacy wall (14 slats). The completed stand-alone 6-post outdoor pergola can be any size up to 24 feet wide by 12 feet deep by 10 feet tall. The steel brackets for the pergola's frame are made for 6x6 wood posts (actual size: 5.5\" x 5.5\"), and the brackets for the roof rafters and privacy wall slats are made for 2x6 wood (actual size: 1.5\" x 5.5\"). The DIY-friendly kit includes stainless steel screws for securing the 6x6 and 2x6 wood posts/slats into the steel brackets. Wood (lumber) not included.
Built with quality. This rafter top pergola kit allows you to accent you pergola top and enjoy the evening sky. Discover the perfect blend of beauty and strength that will transform your outdoor space into a stunning retreat. Canadian-made brackets Weather-resistant coatings 12 gauge steel Just add lumber Quick Installation
- - For 4x4 (3.5" x3.5") Posts - - For 4x4 (3.5" x3.5") Posts- - For 4x4 (3.5" x3.5") Posts We make these and all our PostHugger brackets ourselves in Cartersville, GA. This listing is for our Outside Corners and other individually sold brackets made to fit 4 x 4 Posts and Beams. If you want them for 6 x 6 posts, click here: https://www.etsy.com/listing/708942856 (NOTE: All our brackets are based on the dimensional size of the lumber but we can make them actual 4"x4" or 6"x6" for you, if needed. Just let us know your ship-to zip code, the parts and actual size(s) you would like and we can let you know the total cost for custom brackets made to fit your saw-mill-cut posts.) Build your own rugged and heavy duty PostHugger™ Pergola, Double Pergola, shop/garage/CNC table, deck or even a wedding arch chuppah with our USA made 1/8" steel Outside Corner brackets and more! Also great for fixing/reinforcing the one you already have! These are not flimsy/bendable metal. We make them using 1/8" thick steel - a single corner bracket weighs just over 2 pounds - - strong enough to take what you throw at it (or what you throw it at!), but not so heavy where they are hard to work with. Our brackets can be installed using any 1/2" wood lag screws or in instances where there will not be a collision of bolt holes, 1/2" thru bolts. If you use lag screws, we recommend 1/2" x at least 2" length for 4x4 posts and at least 2.5" length for 6x6 posts, with longer bolts adding more strength. WOOD AND BOLTS/LAG SCREWS ARE NOT INCLUDED WITH OUR BRACKETS. Please note that unless you choose the powder coated option, these ship as raw, unpainted steel. You can either paint them the color of your choice, finish them with a clear coat, or allow to achieve a natural rust patina over time. ***Powder Coated Brackets: If ordering brackets in the black powder coat, please allow an additional 1-2 days for shipping & delivery.*** WHY BUY POSTHUGGER? • We are the original designer of these brackets, often copied by others but never equaled! • We use 1/8″ steel which is thicker than a Quarter and a Dime stacked on top of each other. • Unlike others who just cut and ship steel right off their table, we take the time to hand debur and wire brush both the inside and outside of every piece. • All powder coating is done in-house to ensure a quality application on each and every piece. • We use only 100% first-rate, high quality powders, which are all made in America. • We develop all designs ourselves and, unlike some, never poach the intellectual property of others. • We proudly stand behind all our products. • All our PostHugger™ Brackets & metal artwork products are Made in America with American-Made Steel! *************************** Our Brackets Product Line includes: Outside Corner Brackets - bent at a 90 degree angle to fit over any 4 x 4 post (3.5" x 3.5"). There are two 1/2" holes on each of the top ears for fastening to cross members and four 1/2" holes on the bottom leg for mounting to the legs. (The holes for the legs are offset so that if you want to thru bolt, you don't have to worry about hitting any of the other installed bolts!) Flat T brackets - join other parts of your design. Bent L’s - use where you want an inside corner. Flat L’s - Flat like the T, but without the third leg. Double Inside Corner - This is used on an inside corner to support two incoming posts. The holes are offset so that if used on the same post as an Outside Corner, they will not collide. Two Piece Post Base - Used to bolt a post to concrete or other suitable surface. If your post is going up against a wall or other flat surface which would interfere with having four feet, you will want to use either our Half-a-Post-Base, our 3-Sided Post Base (which has three feet) or our Full Post Base (which has just two feet) so that your post can be closer to a wall. Half a Post Base - This bracket is just one half of the Two Piece Post Base, for those who only need one (or another odd number). Three-Sided Post Base - Similar to our other Post Bases, but with three sides/feet. Full Post Base - Similar to our other Post Bases but with fours sides and just two feet (on opposite sides). Legless T™ - This bracket is the same dimensions & placement of bolt holes as the “T” - just without the bottom “leg” of the “T”! It measures 5.5" x 16.5" for a 6x6 post, and 3.5" x 10.25" for a 4x4 Post. Flat X™ Bracket - 90 degree cross angle brackets to provide extra, heavy duty support to new or existing DIY builds & structures. Flat Knee™ - This knee brace bracket sits flush against the outside of a knee joint. Bent Knee™ - This knee brace bracket is for use where you have a post coming in to meet another post at a 45° angle and want a bracket in the knee bend itself. *****EXTRA SHIPPING COST ON ALL BRACKET ORDERS TO NON-CONTIGUOUS UNITED STATES.***** Please call 470-626-5989 to place your order. If you would like to see customer photos (and a video!) of some of our brackets in use, copy and paste the following URL into your browser: https://posthugger.com/photos/ © 2024 Thermo-Flex Technologies, Inc. - All Designs, Photos, and Text are the Intellectual Property of Shop Owner and are not to be copied without express written permission.
This DIY pergola kit contains all the brackets and hardware you'll need to build your own pergola off back of house with roof (14 traditional roof rafters atop beams) and a privacy wall (8 slats). The attached-to-house pergola can be any size up to 24 feet wide (attached to house) by 24 feet deep (out from home) by 10 feet tall. The steel brackets for the pergola's frame are made for 6x6 wood posts (actual size: 5.5\" x 5.5\"), and the brackets for the traditional roof rafters and wall slats are made for 2x6 wood (actual size: 1.5\" x 5.5\"). The DIY-friendly kit includes stainless steel screws for securing the 6x6 and 2x6 wood into the steel brackets. Wood (lumber) not included.
- - For 4x4 (3.5" x3.5") Posts - - For 4x4 (3.5" x3.5") Posts- - For 4x4 (3.5" x3.5") Posts This listing is for our Outside Corners and other individually sold brackets made to fit 4 x 4 Posts and Beams. If you want them for 6 x 6 posts, click here: https://www.etsy.com/listing/708942856 (NOTE: All our brackets are based on the dimensional size of the lumber but we can make them actual 4"x4" or 6"x6" for you, if needed. Just let us know your ship-to zip code, the parts and actual size(s) you would like and we can let you know the total cost for custom brackets made to fit your saw-mill-cut posts.) Build your own rugged and heavy duty PostHugger™ Pergola, Double Pergola, shop/garage/CNC table, deck or even a wedding arch chuppah with our USA made 1/8" steel Outside Corner brackets and more! Also great for fixing/reinforcing the one you already have! These are not flimsy/bendable metal. We make them using 1/8" thick steel - a single corner bracket weighs just over 2 pounds - - strong enough to take what you throw at it (or what you throw it at!), but not so heavy where they are hard to work with. Our brackets can be installed using any 1/2" wood lag screws or in instances where there will not be a collision of bolt holes, 1/2" thru bolts. If you use lag screws, we recommend 1/2" x at least 2" length for 4x4 posts and at least 2.5" length for 6x6 posts, with longer bolts adding more strength. WOOD AND BOLTS/LAG SCREWS ARE NOT INCLUDED WITH OUR BRACKETS. Please note that unless you choose the powder coated option, these ship as raw, unpainted steel. You can either paint them the color of your choice, finish them with a clear coat, or allow to achieve a natural rust patina over time. ***Powder Coated Brackets: If ordering brackets in the black powder coat, please allow an additional 1-2 days for shipping & delivery.*** WHY BUY POSTHUGGER? • We are the original designer of these brackets, often copied by others but never equaled! • We use 1/8″ steel which is thicker than a Quarter and a Dime stacked on top of each other. • Unlike others who just cut and ship steel right off their table, we take the time to hand debur and wire brush both the inside and outside of every piece. • All powder coating is done in-house to ensure a quality application on each and every piece. • We use only 100% first-rate, high quality powders, which are all made in America. • We develop all designs ourselves and, unlike some, never poach the intellectual property of others. • We proudly stand behind all our products. • All our PostHugger™ Brackets & metal artwork products are Made in America with American-Made Steel! *************************** Our Brackets Product Line includes: Outside Corner Brackets - bent at a 90 degree angle to fit over any 4 x 4 post (3.5" x 3.5"). There are two 1/2" holes on each of the top ears for fastening to cross members and four 1/2" holes on the bottom leg for mounting to the legs. (The holes for the legs are offset so that if you want to thru bolt, you don't have to worry about hitting any of the other installed bolts!) Flat T brackets - join other parts of your design. Bent L’s - use where you want an inside corner. Flat L’s - Flat like the T, but without the third leg. Double Inside Corner - This is used on an inside corner to support two incoming posts. The holes are offset so that if used on the same post as an Outside Corner, they will not collide. Two Piece Post Base - Used to bolt a post to concrete or other suitable surface. If your post is going up against a wall or other flat surface which would interfere with having four feet, you will want to use either our Half-a-Post-Base, our 3-Sided Post Base (which has three feet) or our Full Post Base (which has just two feet) so that your post can be closer to a wall. Half a Post Base - This bracket is just one half of the Two Piece Post Base, for those who only need one (or another odd number). Three-Sided Post Base - Similar to our other Post Bases, but with three sides/feet. Full Post Base - Similar to our other Post Bases but with fours sides and just two feet (on opposite sides). Legless T™ - This bracket is the same dimensions & placement of bolt holes as the “T” - just without the bottom “leg” of the “T”! It measures 5.5" x 16.5" for a 6x6 post, and 3.5" x 10.25" for a 4x4 Post. Flat X™ Bracket - 90 degree cross angle brackets to provide extra, heavy duty support to new or existing DIY builds & structures. Flat Knee™ - This knee brace bracket sits flush against the outside of a knee joint. Bent Knee™ - This knee brace bracket is for use where you have a post coming in to meet another post at a 45° angle and want a bracket in the knee bend itself. *****EXTRA SHIPPING COST ON ALL BRACKET ORDERS TO NON-CONTIGUOUS UNITED STATES.***** Please call 470-626-5989 to place your order. If you would like to see customer photos (and a video!) of some of our brackets in use, copy and paste the following URL into your browser: https://posthugger.com/photos/ © 2024 Thermo-Flex Technologies, Inc. - All Designs, Photos, and Text are the Intellectual Property of Shop Owner and are not to be copied without express written permission.
BUILT TO LAST TRIO is our 90 ̊ 3-arm corner bracket for our pergola system. It is the cornerstone of our modular pergola system. SPECS Category: 6x6 Arm Opening (Interior): 5.62” x 5.62” Arm Opening (Exterior): 5.828” x 5.828” Arm Height: 9” Gauge: 12-gauge Canadian Steel Overall Size (1 Pc.): LxWxH: 14.75” x 14.75” x 14.75” Colour: Black Weight (4 Pc.): 45 lbs. Fastening Holes: 0.25” Securing Holes: 0.5” FEATURES 12-gauge Canadian Steel Canadian Made Brackets Weather-Ready: Coated in weather-resistant materials (E-Coat and Powder Coating) Laser-cut, bent, and welded All hardware, to secure to lumber, is included Packaged with #12x1-1/2” Pan Rob/Phil combo drive 304 S.S Wood screws with black plastic head caps Welds on the inside for a clean quality look Recyclable 5-year limited warranty 8 fastening holes per side for attaching accessories INCLUDED IN KIT 2 x TRIO 3 Arm Pergola Corner Bracket for 6x6 Wood Posts #12 x 1-1/2” Pan Rob/Phil combo drive 304 S.S Wood screws with Black plastic head caps NOT INCLUDED WoodShipping wood is costly. Most of the population has access to stores that sell wood locally where they live. Buying your lumber allows you the freedom to select the type of wood you want to use for your build and budget. There are also regional limitations for what kind of lumber is ideal your build; different species of lumber would be used in tropical climate vs. a cold one. TIPS GENERAL We recommend taking a bracket with you when you purchase your wood to test fit. WOOD Our 6x6 brackets accommodate dressed lumber, commonly called 6x6’s at local building supplies. The actual measure is 5.5x5.5”. If purchasing wood from a lumber yard, or you prefer using Rough Cut vs. Dressed wood please reach out to [email protected] SCREWS You only require 2 screws per each side ofthe bracket (e.g. 12 per TRIO). Insert screws in holes closest to the wood. Hardware to secure to wood is included. Additional screws are available for purchase
- - For 6x6 (5.5”x5.5”) Posts & Beams - - For 6x6 (5.5”x5.5”) Posts & Beams - - For 6x6 (5.5”x5.5”) Posts & Beams This listing is for our Outside Corners and other individually sold brackets made to fit 6 x 6 posts and beams. If you want the same thing, but for 4 x 4 posts and beams, click here https://www.etsy.com/listing/725042533 (NOTE: All our brackets are based on the dimensional size of the lumber but we can make them actual 4"x4" or 6"x6" for you, if needed. Just let us know your ship-to zip code, the parts and actual size(s) you would like and we can let you know the total cost for custom brackets made to fit your saw-mill-cut posts.) Build your own rugged and heavy duty PostHugger™ Pergola, Double Pergola, shop/garage/CNC table, deck or even a wedding arch/chuppah with our USA made 1/8" steel Outside Corner brackets and more! Also great for fixing/reinforcing the one you already have! These are not flimsy/bendable metal. We make them using 1/8" thick steel - a single 6x6 corner bracket weighs about 6 pounds - - strong enough to take what you throw at it (or what you throw it at!), but not so heavy where they are hard to work with. WHY BUY POSTHUGGER? • We are the original designer of these brackets, often copied by others but never equaled! • We use 1/8″ steel which is thicker than a Quarter and a Dime stacked on top of each other. • Unlike others who just cut and ship steel right off their table, we take the time to hand debur and wire brush both the inside and outside of every piece. • All powder coating is done in-house to ensure a quality application on each and every piece. • We use only 100% first-rate, high quality powders, which are all made in America. • We develop all designs ourselves and, unlike some, never poach the intellectual property of others. • We proudly stand behind all our products. • All our PostHugger™ Brackets & metal artwork products are Made in America with American-Made Steel! *************************** We get a lot of questions about how to build a double pergola (one with six legs) like you may have seen in one of our photos - they use the following: 4 Outside Corners 2 Flat T 8 Bent L Inside Corners 6 Full Post Bases (or 6 of our Two-Piece Post Bases) Our brackets can be installed using any 1/2" wood lag screws or in instances where there will not be a collision of bolt holes, 1/2" thru bolts. If you use lag screws, we recommend 1/2" x at least 2" length for 4x4 posts and at least 2.5" length for 6x6 posts, with longer bolts adding more strength. WOOD AND BOLTS/LAG SCREWS ARE NOT INCLUDED WITH OUR BRACKETS. Please note that unless you choose the powder coated option, these ship as raw, unpainted steel. You can either paint them the color of your choice, finish them with a clear coat, or allow to achieve a natural rust patina over time. ***Powder Coated Brackets: If ordering brackets in the black powder coat, please allow an additional 1-2 days for shipping & delivery.*** Our Brackets Product Line includes: Outside Corner Brackets - bent at a 90 degree angle to fit over any 6 x 6 post (5.5" x 5.5"). There are two 1/2" holes on each of the top ears for fastening to cross members and four 1/2" holes on the bottom leg for mounting to the legs. (The holes for the legs are offset so that if you want to thru bolt, you don't have to worry about hitting any of the other installed bolts!) Flat T brackets - join other parts of your design. Bent L’s - use where you want an inside corners. Flat L’s - Flat like the T, but without the third leg. Double Inside Corner - This is used on an inside corner to support two incoming posts. The holes are offset so that if used on the same post as an Outside Corner, they will not collide. Two Piece Post Base - Used to bolt a post to concrete or other suitable surface. If your post is going up against a wall or other flat surface which would interfere with having four feet, you will want to use either our Half-a-Post-Base, our 3-Sided Post Base (which has three feet) or our Full Post Base (which has just two feet) so that your post can be closer to a wall. Half a Post Base - This bracket is just one half of the Two Piece Post Base, for those who only need one (or another odd number). Three-Sided Post Base - Similar to our other Post Bases, but with three sides/feet. Full Post Base - Similar to our other Post Bases but with fours sides and just two feet (on opposite sides). Full Post Base - Similar to our other Post Bases but with fours sides and just two feet (on opposite sides). Legless T™ - This bracket is the same dimensions & placement of bolt holes as the “T” - just without the bottom “leg” of the “T”! It measures 5.5" x 16.5" for a 6x6 post, and 3.5" x 10.25" for a 4x4 Post. Flat X™ Bracket - 90 degree cross angle brackets to provide extra, heavy duty support to new or existing DIY builds & structures. *****EXTRA SHIPPING COST ON ALL BRACKET ORDERS TO NON-CONTIGUOUS UNITED STATES.***** Please call 470-626-5989 to place your order. If you would like to see customer photos (and a video!) of some of our brackets in use, copy and paste the following URL into your browser: https://posthugger.com/photos/ © 2024 Thermo-Flex Technologies, Inc. - All Designs, Photos, and Text are the Intellectual Property of Shop Owner and are not to be copied without express written permission.
This DIY attached 6x6 pergola kit contains all the brackets and hardware you'll need to build your own 6x6 pergola off house with roof. The completed pergola will be 6 feet wide (attached to house) by 6 feet deep (out from the home) and up to 10 feet tall. The weather-resistant, USA-made steel brackets for the pergola's frame are made for 4x4 wood posts (actual size: 3.5 x 3.5 inches). The brackets for the roof rafters are made for either 2x4 wood slats (actual size: 1.5 x 3.5 inches) or for 4x4 posts, depending on the style of roof you select. The kit includes stainless steel screws for securing the 4x4 and 2x4 wood into the steel brackets. Wood (lumber) NOT included.
The 6x6 QUAD 30 allows you to extend your structure beyond our recommended span of 12’, allowing you to create a double pergola structure with a peaked roof. Ideal for larger spaces.
It's tough to find a pergola kit that's totally modular and has the ability to fit the size of any space. With the Bjorn Woodworks Pergola Kit, those days are over. This kit comes equipped with 4 Pergola Bracket Boots, 4 Pergola Bracket Shoulders, and all necessary lag bolts. The size and shape are completely up to you, just cut your timbers to your desired length and depth and assemble."}},"base-catalog-324321395":{"__typename":"BaseProduct Accommodates 4 in. x 4 in. lumber (exact measurement 3.5 in. x 3.5 in.) Finished with flat black powder coating Easy and intuitive installation Box steel design
Description These 3-arm Trio corner brackets are specially designed for wood posts of 4" x 4" (nominal sizes; actual sizes of 3.5" x 3.5") for the construction of a Toja Grid pergola. They are made of zinc-plated 14-gauge steel, with superior quality powder paint, perfect for extended outdoor use. This product is backed by a 2-year limited warranty. Wood screws included. Quality product, made in Canada The cornerstone of the Toja Grid system Note: our brackets are made to fit dressed lumber, 4x4 wood is in fact 3.5-in x3.5-in - the industry simply calls it 4x4 All hardware included to attach to wood Zinc coated with commercial grade outdoor powder coating Built to last; weather-resistant materials Customize and build to your space, size, and design
BUILT TO LAST SOLO is our post base and wall mount bracket. It allows you to mount your structure to a surface or attach it to a wall. The flange has four oversized holes that enable you to secure your pergola to a deck, concrete, brick or any other surface you choose. SPECS Category: 6x6 Arm Opening (Interior): 5.62” x 5.62” Arm Opening (Exterior): 5.828” x 5.828” Arm Height: 9” Gauge: 12-gauge Canadian Steel Overall Size (1 Pc.): LxWxH: 8”x8”x9” Colour: Black Weight (1 Pc.): 8 lbs. Fastening Holes: 0.25” Flange: 1” Securing Holes: 0.5” FEATURES 12-gauge Canadian Steel Canadian Made Brackets Weather-Ready: Coated in weather-resistant materials (E-Coat and Powder Coating) Laser-cut, bent, and welded All hardware, to secure to lumber, is included Packaged with #12x1-1/2” Pan Rob/Phil combo drive 304 S.S Wood screws with black plastic head caps Recyclable 5-year limited warranty 8 fastening holes per side for attaching accessories INCLUDED IN KIT 1 x SOLO Pergola Post Base and Wall Mount Brackets for 6x6 Wood Posts #12 x 1-1/2” Pan Rob/Phil combo drive 304 S.S Wood screws with Black plastic head caps NOT INCLUDED WoodShipping wood is costly. Most of the population has access to stores that sell wood locally where they live. Buying your lumber allows you the freedom to select the type of wood you want to use for your build and budget. There are also regional limitations for what kind of lumber is ideal your build; different species of lumber would be used in tropical climate vs. a cold one. Surface Securing Hardware Due to different building materials and requirements based on location, we always recommend talking to your local hardware store for the best securing hardware for your specific surface. *Before mounting anything to your home or cottage, we also advise on consulting your local building code(s). TIPS GENERAL We recommend taking a bracket with you when you purchase your wood to test fit. WOOD Our 6x6 brackets accommodate dressed lumber, commonly called 6x6’s at local building supplies. The actual measure is 5.5x5.5”. If purchasing wood from a lumber yard, or you prefer using Rough Cut vs. Dressed wood please reach out to [email protected] SCREWS You only require 2 screws per each side ofthe bracket (e.g. 4 per SOLO). Insert screws in holes closest to the wood. Hardware to secure to wood is included. Additional screws are available for purchase
This 6x6 pergola beam bracket makes it easy to assemble the frame of a DIY wood pergola with 2 or more blocks/sections (either free-standing or attached to house). It's made of commercial grade 12-gauge steel (approximately 2.6mm thick) with protective weather-resistant powder coating, ensuring it will look as amazing in ten years as it does now. The steel pergola beam bracket has 4 channels (i.e. 4 arms), one of which is for the vertical post going to the ground and the remaining three of which are for the roof beams. The bracket is made for 6x6 wood posts (actual size: 5.5 x 5.5 inches) and includes stainless steel screws for securing the 6x6 wood posts into the bracket. Wood (lumber) not included.
BUILT TO LAST QUINT is our 5 arm structure expansion bracket. It allows you to connect three pergolas in an ‘L’ shape, or to attach four structures to create a sizeable commercial patio. SPECS Category: 4x4 Arm Opening (Interior): 3.61” x 3.61” Arm Opening (Exterior): 3.75” x 3.75” Arm Length: 7” Gauge: 14-gauge Canadian Steel Overall Size (1 Pc. QUINT): LxWxH: 17.75 x 17.75 x 10.75” Colour: Black Weight (1 QUINT + 1 SOLO): 20 lbs. Fastening Holes: 0.25” FEATURES 14-gauge Canadian Steel Canadian Made Brackets Weather-Ready: Coated in weather-resistant materials (E-Coat and Powder Coating) Laser-cut, bent, and welded All hardware, to secure to lumber, is included Packaged with #12x1-1/2” Pan Rob/Phil combo drive 304 S.S Wood screws with black plastic head caps Welds on the inside for a clean quality look Recyclable 5-year limited warranty 8 fastening holes per side for attaching accessories INCLUDED IN KIT 1 x QUINT 5 Arm Pergola Structure Expansion Bracket for 4x4 Wood Posts 1 x SOLO for 4x4 Wood Posts #12 x 1-1/2” Pan Rob/Phil combo drive 304 S.S Wood screws with Black plastic head caps NOT INCLUDED WoodShipping wood is costly. Most of the population has access to stores that sell wood locally where they live. Buying your lumber allows you the freedom to select the type of wood you want to use for your build and budget. There are also regional limitations for what kind of lumber is ideal your build; different species of lumber would be used in tropical climate vs. a cold one. TIPS GENERAL We recommend taking a bracket with you when you purchase your wood to test fit. WOOD Our 4x4 brackets accommodate dressed lumber, commonly called 4x4’s at local building supplies. The actual measure is 3.5x3.5”. If purchasing wood from a lumber yard, or you prefer using Rough Cut vs. Dressed wood please reach out to [email protected] SCREWS You only require 2 screws per each side ofthe bracket (e.g. 32 per QUINT). Insert screws in holes closest to the wood. Hardware to secure to wood is included. Additional screws are available for purchase
This 6x6 pergola post base bracket makes it easy to secure the post of your DIY wood pergola to a secure foundation (i.e. cement pad, concrete footing, landscape topper, deck footing, etc.). It's made of commercial grade 12-gauge steel (approximately 2.6mm thick) with protective weather-resistant powder coating, ensuring it will look as amazing in ten years as it does now. The steel pergola base bracket is made for 6x6 wood posts (actual size: 5.5 x 5.5 inches) and includes stainless steel screws for securing the post into the bracket. Wood (lumber) not included.